@ Reball expert

[chotky]

Hello i recived to day my ACHI IR6500 station will start making some test very soon , i find this profile on the net for xbox 360 and ps3 please expert can u check if this profile is ok ? picture attached thx , all your comment will be important for me specialy who have ACHI or same

 

[nofeloniesyet]

Hello i recived to day my ACHI IR6500 station will start making some test very soon , i find this profile on the net for xbox 360 and ps3 please expert can u check if this profile is ok ? picture attached thx , all your comment will be important for me specialy who have ACHI or same View attachment 31357

instead of looking on the net for profiles,you should be reading up on how to build your own.not always is a profile someone else uses going to work for you due to a number of reasons.temp, moisture in the air and quite a few other things can effect it.head over to bgamods.com.there is a wealth of this information there,also where i learned to build my own profiles.that forums dedicated to bga rework and repairs in general on these consoles and more.

 

[stucknvegas]

Purchased that same machine and BGA mods helped out allot ..They have tutorials on Building profiles..With there help I found out the bottom heater 800 watt to be way to Small
They had me Remove the glass permanently and Raise the bottom heater up quite a bit..That machine after some modds was ok for slims.. Phats the profile was way to long
I opted for a different Achi with 4 bottom heaters and I changed those as well to 600 watt Elstiens I found that the 6500 Jig support was not very practical as well
You might want to consider all that before opening the box .. My 6500 is collecting dust for a couple years Building profiles is time consuming be patient

 

[Sasuke Uchiha]

Achi sucks ass man. U should have done more research before buying it. You can't do ps3 with that either. Scotle ir6000 or scotle ir pro.

 

[Antalpromille]

Achi sucks ass man. U should have done more research before buying it. You can't do ps3 with that either. Scotle ir6000 or scotle ir pro.

You can't? So those ps3s that I have done on my achi ir6000 doesn't really work? Must have been my imagination.

 

[Sasuke Uchiha]

You can't? So those ps3s that I have done on my achi ir6000 doesn't really work? Must have been my imagination.

Did u do any mods to it. To be able to do ps3s.

 

[Antalpromille]

Did u do any mods to it. To be able to do ps3s.

Nothing more than replacing the TC to a better one.

 

[chotky]

What do u mean with TC , well with this attached profile i remove the GPU without problem and in time the bottom was at 230° is it ok ? now place to reball other hard think , then to replace the GPU will use same profile ?

 

[Sasuke Uchiha]

U need to build your own profile a premade one won't help you. Listen u want the bottom temp to get the board to between 170 and 175 before the top heater kicks in. Then have the top heater temps be

R-1.00 L 170 D 170

R 1.00 L 185 D 20

R 1.00 L 200 D 20

R 1.00 L 210 D 15

R 1.00 L 220 D 15

R 1.00 L 225 D 10

End

Something like that. That's close to my profile but I'm going off the my memory and not looking at my scotle.

 

[nofeloniesyet]

dont even know what tc is and your lookin for premade profiles?........again,this isnt the place for this thread,head over to bgamods.com for this.

 

[chotky]

will use a lead balls , so when reball the gpu the L4 must be max 185° right ? can u give best config for gpu soldering after reball ?

 

[nofeloniesyet]

will use a lead balls , so when reball the gpu the L4 must be max 185° right ? can u give best config for gpu soldering after reball ?

if you would listen and take this to the APPROPRIATE forum you would get alot more help. www.bgamods.com

 

[chotky]

dont even know what tc is and your lookin for premade profiles?........again,this isnt the place for this thread,head over to bgamods.com for this.

the english is not my language im trying to make effort to speak it and write it im sure that the TC is somthing hardware in the station , the station is here from 24h only , here is beginer section so if i dont understand somthing is the good section to ask for it , if admin or moderator dont like my topic who can help many here they can erase it , im beginer and all of you was beginers one day !!!!!!!

 

[nofeloniesyet]

the english is not my language im trying to make effort to speak it and write it im sure that the TC is somthing hardware in the station , the station is here from 24h only , here is beginer section so if i dont understand somthing is the good section to ask for it , if admin or moderator dont like my topic who can help many here they can erase it , im beginer and all of you was beginers one day !!!!!!!

and we all looked at the APPROPRIATE forum,which is bgamods.com.this is an xecuter product support forum,not a reball forum.they speak the same english they do here over at bgamods.