Martin C
VIP Member
Ok - I misread this message - it's not saying incorrect size which is a good thing!
Have you disconnected the external switch as recommended?
Have you disconnected the external switch as recommended?
Refusing to FlashBIOS
- Thread starter knight037
- Start date
I also but everything back together, including the switch (ON RED) switchable from RED to GREEN on the CHIP.
Martin C
VIP Member
Can you try a non-X3 BIOS?
Go back to Xbins and download the X2_5035 BIOS. Extract the version for your Xbox and boot the backup BIOS. Set the switches to banks 78 (512k) by setting them to off off on off off. See if this goes any further.
Martin
Go back to Xbins and download the X2_5035 BIOS. Extract the version for your Xbox and boot the backup BIOS. Set the switches to banks 78 (512k) by setting them to off off on off off. See if this goes any further.
Martin
Ok Obtained the .bin file proceeded to FlashBIOS 3.0.1 screen accepted got hungup on the AMBER status bar everything reads the same as in the TEAMXecuter Tutorial except in between the DO NOT TURN OFF etc.... part and the STATUS BAR it reads "Erase Failed!" and the Eject Button is flashing GREEN\AMBER.
Turned the system off and back on and I'am still able to access the Bank setting 78 off off on off off threw the Backup Bank setting 78(PURPLE LITE).
Last edited:
Well solderless, but I had to solder the the pin removed what #15 to install the D0, read other Threads on double checking #13 and #14 pin for contact, do not have device to check for connectivity.....
So to make a long story short the solder one, not the one that LITESup.
So to make a long story short the solder one, not the one that LITESup.
what pin do you mean the pin header or the pin that go into the d0 point on motherboard
you do have this xapter
is it one of these legs
you do have this xapter
is it one of these legs
Last edited:
No the other one.....
You might as well read BELOW.
Yeah PINHEADER v1.6, so ok when I installed the pinheader I negleted to take out the #6 and turned it ON "if I may correct my self from above" "or at all" and also did not install the D0 rebuild pcb (BEGINNERS ERROR!!!) but since then have managed to put it all together and it all LITES UP get all the screens, may be I shorted something out in there, therefore it's not reading the .bin files correctly.
You might as well read BELOW.
Yeah PINHEADER v1.6, so ok when I installed the pinheader I negleted to take out the #6 and turned it ON "if I may correct my self from above" "or at all" and also did not install the D0 rebuild pcb (BEGINNERS ERROR!!!) but since then have managed to put it all together and it all LITES UP get all the screens, may be I shorted something out in there, therefore it's not reading the .bin files correctly.
Last edited:
is the d0 solded onto the rebuild
part 11 on page 2 of this guide
http://teamxecuter.entryhost.com/x3ce.pdf
all so page 9
part 11 on page 2 of this guide
http://teamxecuter.entryhost.com/x3ce.pdf
all so page 9
Last edited:
Yeap I used a COLD\HEAT solderer which should have prevented me from heating up the board to much and using as little solder as possible making the sure by returning to each points to make sure the solder made adequate or correct connection, connected the GREY WIRE, the RED and GREEN WIRE as in the instructions. the single RED1.5v as well and all others from the CHIP also as in the instructions, what would be the BLACK WIRE for the switch and the other RED WIRE double red to the EJECT\POWER button.
Everything LIT-UP. "FlashBIOS 3.0.1 screen(s) and Xbox screen.
Everything in that order.
Everything LIT-UP. "FlashBIOS 3.0.1 screen(s) and Xbox screen.
Everything in that order.
Last edited:
don't know but theres the first problem there
you say it dose not heat the solder up but it use a cold solder to solder the pins should of used a 15w to 30w soldering iron
as shown in guide
13. Soldering iron (max. 30Watt, with small sharp tip. Smaller equals more control!)
14. Solder (resin core recommended, and the thinner the better)
15. Flux (optional)
this all so may be your problem but with out another chip you can,t check
you can try to check voltage of LPC
http://xbox-scene.com/articles/lpc-diag.php
i suggest you read the guide below from start to finish then read them again
http://teamxecuter.entryhost.com/x3ce.pdf
http://www.team-xecuter.com/flashbios/
http://www.epemag.com/solderfaq/pictures.htm
don't know but theres the first problem there
you say it dose not heat the solder up but it use a cold solder to solder the pins should of used a 15w to 30w soldering iron
as shown in guide
13. Soldering iron (max. 30Watt, with small sharp tip. Smaller equals more control!)
14. Solder (resin core recommended, and the thinner the better)
15. Flux (optional)
this all so may be your problem but with out another chip you can,t check
you can try to check voltage of LPC
http://xbox-scene.com/articles/lpc-diag.php
YOU CHECK THE TOP SIDE OF MOTHER BOARD ON THE PIN HEADER
i suggest you read the guide below from start to finish then read them again
http://teamxecuter.entryhost.com/x3ce.pdf
http://www.team-xecuter.com/flashbios/
http://www.epemag.com/solderfaq/pictures.htm
UNLESS MARTIN CAN HELP
Last edited:
Ok........READING.........I SEE:|
FYI: Did not have any of the 1.5v connections (TOGETHER) seperate occasions?
FYI: Did not have any of the 1.5v connections (TOGETHER) seperate occasions?
Last edited:
Ok it's tommorro checked continuity and I'am not recieving the 3.3v like I should be http://xbox-scene.com/articles/lpc-diag.php, I will now obtain a hotter iron and someother essentials as requested.
AGAIN THX, much appretiated.......
AGAIN THX, much appretiated.......