LITEON DG-16D2S replacement drive no key want to flash 0800

K

killerbobman

Noob Account
Jan 15, 2012
4
0
Man I feel stupid - I can figure out what my issue is. aahh

i have a x360usb v18
ck3i
jungle flasher .192
win7 64bit
drivers loaded for both x360usb adn ck3i

I need some help on flashing 0800 on my liteon so I can backup xbox 360 games

I thought I got it flashed right but xbc will not open and
i cannot get the ck3i to eject my dirive so i must be a flash issue.

the drive does eject fine in a xbox360
lights on the x360usb 2 green and blue
jf will not eject dirve but will power cycle with green light going on and off
x360usb has a green light and red light

power to the cx3i is direct for computer power supply

Thank you in advance
 
V

Vest1ge

check the ck3I is powered on, it should have an orange and green light. And cable connected properly, it wont be a firmware issue if the console is ejecting the drive.
 
K

killerbobman

Noob Account
Jan 15, 2012
4
0
yes ck3i is powered on
I have searched online and gone over what other people says the lights should be and I get the correct lights.
the ck3i does power on/off and cycle in JF
but the open/close and half buttons do not doe anything.
When out of jungle flash i get a blue or red light depending on the button
power light is green
manual light is yellow and goes to blue in jf
I press the eject button and it does not do anything.

Can anyone refer me to the directions on flashing a REFERBISHED drive with 0800?

could my ck3i be bad if that was true then if I ejected the drive with my xbox 360 put a dish in and then hooked it to my computer i should be able to back it up and that does not work either.

---------- Post added at 10:39 ---------- Previous post was at 10:38 ----------

ohh i have a liteon DG-16d2s and have also tried a benq with the same results
 
K

killerbobman

Noob Account
Jan 15, 2012
4
0
I reflashed the drive again
when I goto device manager the device shows up
but when I goto my computer and right click my computer stops responding




~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
JungleFlasher 0.1.92 Beta (304)
Session Started Sat Jan 28 12:36:13 2012

This is a Wow 64 process running on 4 x 64 bit CPUs
X360USB PRO detected, Version 0.18

Found 1 I/O Ports.
Found 2 Com Ports.
Found 4 windows drives C: D: E: H:
Found 0 CD/DVD drives

Loading firmware file D:\Video Games\XBOX360\Xbox360 Mod\Get Firmware from DVD\Latest_iXtreme_and_Stock_Firmware_Pack_(with_BenQ_and_Phat_Lite-On_v3.0)\0800_BenQ and phat Lite-on v3\LT-liteon-0800-v3.bin
MD5 hash: 777e8c2d89e0f57f891aa6735ed1cc95
Genuine Lite-On LT 0800 v3
Drive key @ n/a 55AA55AA55AA55AA55AA55AA55AA55AA
Firmware Osig: [PLDS DG-16D2S 7485]
Firmware is: LITEON-AP25V3.0 DG-16D2S

Sending Lite-On-Erase request to port 0x0000
..
Drive returned Status 0x80
.........
Serial flash found with Status 0x72
Manufacturer ID: 0xC2
Device ID: 0x11
Flash Name: MXIC(MX25L2005)
Flash Size: 262144 bytes
Sending Vendor Intro to port 0x0000

Serial flash found with Status 0x72

Sending Device ID request to port 0x0000
Spi Status: 0x00
Manufacturer ID: 0xC2
Device ID: 0x11
Flash Name: MXIC(MX25L2005)
Flash Size: 262144 bytes

Getting Status from port 0x0000
SPi flash found with Status 0x72

Sending Chip Erase to Port 0x0000
Erasing:
Blank Test !

Reading Bank 0: ................
Reading Bank 1: ................
Reading Bank 2: ................
Reading Bank 3: ................
Blank verified OK !

Getting Status from port 0x0000
SPi flash found with Status 0x72

Sending Chip Erase to Port 0x0000
Erasing:
Writing target buffer to flash
Writing Bank 0: ................
Writing Bank 1: ................
Writing Bank 2: ................
Writing Bank 3: ................

Flash Verification Test !
Reading Bank 0: ................
Reading Bank 1: ................
Reading Bank 2: ................
Reading Bank 3: ................
Write verified OK !
 
K

killerbobman

Noob Account
Jan 15, 2012
4
0
stupid I finally figured this issue out
I bought a new ck3i and a new ck3 mini because my drive was not ejecting.
The new units had the same issue.
If I hooked up via the usb to molex power and to the internal molex to external molex/sata adapter the goes into the back of your computer so you do not have to open it up all the time.
So I finally bypassed the internal to ext molex adapter and it worked aahhh.
:eek2:
bad adapter not a bad ck3i or ck3mini but also the usb to molex would not eject 3 seperate drives fyi
 
You must log in or register to reply here.