LITEON 0225 replacement tx pcb problem

A

alvin101

Junior Member
Apr 19, 2009
19
0
OBLIVION
I bought a replacement tx pcb and I followed the team xecuter tutorial. I get to the part where I connect the board and I have to put it in vendor mode. I press intro and I power cycle the drive. Then I get a pop up saying "Device ID failed please return MRA hack device to normal position! Then, press OK to continue". This confuses me does it suppose to say that when I'm trying to put a blank tx pcb in vendor mode? Look at the attached picture for my current flash properties. For flash chip name it says unknown type. So when I try to write it tells me "
Unknown flash type Write aborted !" How can I get this working? I'm using a x360 USB pro along with a ck3 and the power cable that comes with the team xecuter probe 3.
 
A

alvin101

Junior Member
Apr 19, 2009
19
0
OBLIVION
BL4K3Y said:
Have you tried Lite-On Erase like the tutorial suggests?
Click to expand...
Yes sir many times:(

---------- Post added at 08:27 ---------- Previous post was at 08:25 ----------
BL4K3Y said:
Have you tried Lite-On Erase like the tutorial suggests?
Click to expand...
Travo112 said:
If that doesn't work sometimes you need to probe the pcb.. But that can be found searching


Sent from my iPhone 4s using Tapatalk
Click to expand...
Probe the pcb? with the probe 3? I will search because I am desperate to get this working. I don't suppose you can send me a link just in case I don't find it. Thanks for your reply
 
A

alvin101

Junior Member
Apr 19, 2009
19
0
OBLIVION
marshamods said:
The pcb should intro no problem with the x360usb.


Sent from my iPhone using Tapatalk
Click to expand...
I know:( but it isn't. Do you have any ideas?

---------- Post added at 09:35 ---------- Previous post was at 09:33 ----------
Travo112 said:
I'll dig around once I get home


Sent from my iPhone 4s using Tapatalk
Click to expand...
I've been searching for hours and I haven't found it. Would appreciate if you look for it when you reach home. thanks
 
A

alvin101

Junior Member
Apr 19, 2009
19
0
OBLIVION
GadgetCat said:
Have you got it set to phat? I have TX pcb, no need to probe or anything like that, detected finewhen you hit intro with x360usb

You should post JF log to get the best advice.

Or read this from like step 9 http:// team-xecuter.com/forums/showthread.php?t=67780
Click to expand...
JungleFlasher 0.1.92 Beta (304)
Session Started Sun Apr 22 13:43:21 2012

This is a Wow 64 process running on a 64 bit CPU
X360USB PRO detected, Version 0.18

Found 1 I/O Ports.
Found 2 Com Ports.
Found 4 windows drives C: D: E: G:
Found 1 CD/DVD drives E:

Sending Vendor Intro to port 0x0000
Status 0x80
Re-sending Vendor Intro:
......................
Serial flash found with Status 0x72

Sending Device ID request to port 0x0000
Spi Status: 0xFF
Manufacturer ID: 0xFF
Device ID: 0xFF
Flash Name: Unknown type
Flash Size: n/a
Unknown flash type Write aborted !
 
G

GadgetCat

Full Member
Dec 6, 2011
29
0
Sorry, I can't suggest anything useful, beyond standard fault finding - try to reset the usbpro, try another usb pro, try it on another pc..

Have you got your original board, does the usbpro read it ok?

Just trying to narrow down the exact cause of the error message..
 
Last edited:
You must log in or register to reply here.