Utmad
VIP Member
GeekHeat
VIP Member
ok not to be a smart ass but right here we are in the RGH/JTAG for noobs and if I opened a thread here it means that I want to RGH my console and if I said got all is needed means that got all chips that are needed to RGH a console and if I
wrote retrieve my dvd key and get my console back to stock means that I want to RGH just for that case flash LTU2 firmware to my new board and play backups and be safe on live ,thats all
but anyway thanks a lot your answers, were pretty cleared. IF ANYONE POST IN THE NOOD ROOMS IT DOESNT MEANS HE IS A TOTAL JERK IT MEANS THAT NEEDS A LITTLE HELP
I THINK THAT NOW i'M CLEARED ENOUGH IN WHAT I NEED WITH THIS OPENED THREAD
wrote retrieve my dvd key and get my console back to stock means that I want to RGH just for that case flash LTU2 firmware to my new board and play backups and be safe on live ,thats all
but anyway thanks a lot your answers, were pretty cleared. IF ANYONE POST IN THE NOOD ROOMS IT DOESNT MEANS HE IS A TOTAL JERK IT MEANS THAT NEEDS A LITTLE HELP
I THINK THAT NOW i'M CLEARED ENOUGH IN WHAT I NEED WITH THIS OPENED THREAD
Last edited by a moderator:
Utmad
VIP Member
Yes but to be fair you gave us no information about what you were trying to do, more information is better than virtually none..
Utmad
VIP Member
So you want to RGH the console to get the information for the LTU2 board.
Do you have a glitch chip at all and the tools to read/write to the nand and obviously soldering equipment and skills ?
Is it definitely a Hitachi drive in this trinity or a Lite On, I know some trinities do have the DL10 drive in them as I have one.
Do you have a glitch chip at all and the tools to read/write to the nand and obviously soldering equipment and skills ?
Is it definitely a Hitachi drive in this trinity or a Lite On, I know some trinities do have the DL10 drive in them as I have one.
Last edited:
yes it is dl10 hitachi and have all skills and equipment
THANKS FOR NOT JOKING AROUND AND FOR UNDERSTANDING MY POINT OF THIS THREAD
I think these steps are simple
1 read my orig nand and save it somewhere secure
2 set up J-PROGRAMMER with latest dashboard (16747)
3 create ECC image
4 write ECC image
5 boot into xell with the proper tune that makes my trinity boot in good times
6 get cpu/dvd key and save them
till here I.m ok but after this I have a question
can I just after those steps desolder everything from my motherboard and flash the dvd key on the LTU2 for hitachi ,would my console boot normally and play burned dvds,
OR i NEED FURTHER STEPS DO DO SO ?
THANKS IN ADVANCE FOR YOUR REPLIES ?
THANKS FOR NOT JOKING AROUND AND FOR UNDERSTANDING MY POINT OF THIS THREAD
I think these steps are simple
1 read my orig nand and save it somewhere secure
2 set up J-PROGRAMMER with latest dashboard (16747)
3 create ECC image
4 write ECC image
5 boot into xell with the proper tune that makes my trinity boot in good times
6 get cpu/dvd key and save them
till here I.m ok but after this I have a question
can I just after those steps desolder everything from my motherboard and flash the dvd key on the LTU2 for hitachi ,would my console boot normally and play burned dvds,
OR i NEED FURTHER STEPS DO DO SO ?
THANKS IN ADVANCE FOR YOUR REPLIES ?
Last edited by a moderator:
Read the nand twice with the jr programer make sure they match.
Create the ecc then write the ecc.
Then install your coolrunner to boot to xell.
Get the CPU key etc over LAN.
Jrunner should then automatically extract the key.bin and CR.bin that you need for ltu firmware.
You can then write the original nand back to the console and remove everything you installed.
Then follow the ltu2 tutorial.
Create the ecc then write the ecc.
Then install your coolrunner to boot to xell.
Get the CPU key etc over LAN.
Jrunner should then automatically extract the key.bin and CR.bin that you need for ltu firmware.
You can then write the original nand back to the console and remove everything you installed.
Then follow the ltu2 tutorial.
EVERY THINK OK mY FIRST LTU FLASHED AFTER RGH AND WRITE MY ORIG NAND NOW I'M BACK TO MY FIRST ONE THAT HAS A WRONG NAND AND TRY TO FIX WITH MY ORIGINAL NANDS THAT I ALREADY SAVED
THANKS TO ALL WHO POSTED HELPFUL POSTS TO ME
REGARDS
THANKS TO ALL WHO POSTED HELPFUL POSTS TO ME
REGARDS
you have to write back stock nand b4 you can play anything...
becouse anything it can boot if you dont is only Xell
so... next will be for you
write back original nand or make a retail nand with jrunner (using your CPU key and extracted nand).