Rgh 1.0 jasper 16mb wont boot

[XMODDERCHI3750]

Wassup I tried to RGH a jasper 16mb console CR rgh 1.0 REV A everything when well as this is the 23 console i have RGH 22 falcons all boot with 1 glitch instant boot perfect ones Jasper not so lucky i dump both nands no difference found no bad blocks found i created the image flashed the ecc file programmed the CR program sucess i switched the CR to NOR red light on CR comes on cut on console fan running no green light on the CR and no video or sound either left it on for 30mins nothing i looked around and seen some people programming the CR with the falcon timing files i did it used the 1ft Hi-Grade Low-Loss 50 ohm Double Shielded Cable and the 68nF 50V Ceramic Capacitorthat came with the CR i checked my soldering looks good to me but i posted pics of it i pull it to the side for now if any one has any ideas on how to fix this hit me up heres the link to the pics https://www.dropbox.com/sh/23wrqjp2wu5cmx6/0o2lCxt4Cq

 

[BL4K3Y]

Can you take a clearer image of CPU_PLL_BYPASS please.

We also need to see an image of CPU_RST and CPU_PLL_BYPASS wire locations as well as your image creation logs.

 

[XMODDERCHI3750]

ok i took some better pics now about the image creation logs do it automaticly save or did i have to manual save it because i did this last night and have since close out of all the programs and here is the pics https://www.dropbox.com/sh/23wrqjp2wu5cmx6/0o2lCxt4Cq

 

[BL4K3Y]

Move your CPU_RST wire up towards the X-Clamps or fetch it down to the bottom of the board, it is currently placed in the interference zone.

 

[XMODDERCHI3750]

awwww ok thanks I'm going to do that and post the results thanks again

Edit: just did what u said still nothing should i add a 10 ohm resistor to the cpu rst line?

 

[Martin C]

Can you post your J-Runner logs ?

 

[XMODDERCHI3750]

i run my nand dumps through it right?

Edit:i never used Jrunner thats why I'm asking

 

[Martin C]

So post the logs of whatever app you're using.

 

[XMODDERCHI3750]

i did a bone head move didnt save any logs i though they saved by default so i guest i'm screwed :facepalmn this one i found two more falcon boards that worked but no drive drive so i took the CR out the jasper and put in falcon and bam instant boot everything good so i know it wasnt the CR if anyone got any other ideas i'm open guess i'll sale it on the CL

 

[sick360mods]

You can send it to me and ill get it working for free

Pro bono work for the next 5 people. contact me for details

 

[XMODDERCHI3750]

what do i need to send you ?

 

[sick360mods]

Email me all the files you have or just write the original back into the motherboard. All I need is the motherboard and coolrunner

Pro bono work for the next 5 people. contact me for details

 

[sick360mods]

Pm sent

Pro bono work for the next 5 people. contact me for details

 

[Statecowboy]

Have you tried writing back your original nand dump?

 

[XMODDERCHI3750]

@ StateCowboy naw i just saw that in someone else post so i'm gonna try tomorrow i'm gonna rgh these falcons first seeing i have had 100 percent sucess rate so far with them 22/22 i got 4 more jasper i wanna rgh just need to see what i'm doing wrong @sick360mods i can email u the 2 nand dumps and image bin thats as far as i got I'll pm them to you in the morning thanks for the help people