Rgh Botting But Blinking Light

[dil_king]

Hi so I did the Rgh I installed everything and when I turn on the xbox I get blinking green light but I can hear the fan restarting on my slim and I also has bad block in my nand I had 1 bad block

 

[SamDoleBob]

Do you get it to boot?

 

[dil_king]

nope

 

[SamDoleBob]

Can I assume "Botting" means booting if so I don't understand your problem.

---------- Post added at 23:13 ---------- Previous post was at 23:12 ----------

Did you dump the nand twice and no differences detected?

---------- Post added at 23:15 ---------- Previous post was at 23:13 ----------

If so is it a correct bad block?
Is the motherboard a Trinity or Corona?

 

[dil_king]

It did not boot the bad block not fixed and the mobo is trinity and the nand compare came clean

 

[SamDoleBob]

What tutorial did you follow? It is common to have bad blocks that does not mean it will not work. Open the nand in 360 flash tool click the bad block tab and take a screenshot and post it.

 

[dil_king]

here you go

 

[Justice1231]

You might want to take pictures of your install, concentrating on your solder points. if youve got a camera with the macro facility please use it.

 

[SamDoleBob]

Check your soldering for your nand. Correct bad blocks should look like this:

Note: Bad Block ID 0x0349 [Offset: 0x00D8D200]

-> Block ID 0x0349 found @ 0x3FD [Offset: 01073A00]

Have you made you ecc file and tried to write it?

 

[dil_king]

would my xbox boot if i took off the coolrunner

 

[superspeed]

Not if you've written to the nand unless you flash the original nand back on. Post pics of your install.

 

[dil_king]

Check your soldering for your nand. Correct bad blocks should look like this:

Note: Bad Block ID 0x0349 [Offset: 0x00D8D200]

-> Block ID 0x0349 found @ 0x3FD [Offset: 01073A00]

Have you made you ecc file and tried to write it?

if you take a look at my screenshot it did not tell me the offset how do I get it ?

 

[SamDoleBob]

Have you tried to write the ecc file?

 

[superspeed]

if you take a look at my screenshot it did not tell me the offset how do I get it ?

Don't worry about the bad block. Post pic's of install.

 

[SamDoleBob]

You get that by getting a correct nand dump...

---------- Post added at 23:45 ---------- Previous post was at 23:44 ----------

Don't worry about the bad block. Post pic's of install.

I agree lets see some pics to decide where to go next.

 

[dil_king]

yes I have written the Ecc I have done everything but now I took off coolrunner

 

[SamDoleBob]

Well since you have written the ecc file your xbox wont boot. You need to write your original nand back if you want to keep your box retail. Did you program the coolrunner?

 

[dil_king]

pics of nand x

 

[dil_king]

yes I programmed the cool runner

---------- Post added at 01:10 ---------- Previous post was at 01:01 ----------

what offset would I type In to remap or fix the nand

 

[SamDoleBob]

It looks like you may have some bridged connections and cold solder joints. Also the leads that you soldered should not have blobs like that it can cause shorts and lead to bad reads and writes. That yellow wire should not go around back like that. I think you should get the qsb for the slim and use flux.