RGH-obtained keys-need help

[Buljo]

I got problem with slim consoles....i have obtained key via RGH ,drive is 9504...Is there a way to put that key in a replacement board ? Problem is that console stuck at update...I have tried via Jungleflasher but i have read somwhere that it is not possoble yet to put obtained key to rerplacement board with jugleflasher....please i need help if is possible to put key at unlocked pcb board if not what is possible solution of problem?

 

[crono1000]

Putting it into a unlocked pcb should work just fine. Just make sure you flash stock so the update can go through correctly.

What dash were you on and what dash were you updating to?

Sent from my LG-P999 using Tapatalk 2

 

[metaljay]

I'm curious, why do you want the flash the drive when you have it RGH?
Its easier just to convert your DVD's to GOD's

 

[Buljo]

Dont know....i got that console with that problem so i pressume it was before 14699 update...i tried to put obtained key via jungleflasher but nothing happens....is there some other way to put obtained key and do i need to spoof with original or 0272 firmware?

---------- Post added at 07:28 ---------- Previous post was at 07:27 ----------

I'm curious, why do you want the flash the drive when you have it RGH?
Its easier just to convert your DVD's to GOD's
**************************************************************************
Cause i want that dvd drive work normal without Coolrunner on it....dont know....what to do?

 

[crono1000]

Ok, so you're above 13599. You will need a replacement PCB ($60 on xconsoles) or if you have MXIC and some soldering skills, a sputnik360 ($8 on xconsoles) to be able to flash the drive. You will want the newest stock as well - 0272. That's what all drives have been changed to and why it depends how far updated you are. 9504 used to be flashable until m$ changed it with updates.

Sent from my LG-P999 using Tapatalk 2

 

[Fisticuffs]

Dont know....i got that console with that problem so i pressume it was before 14699 update...i tried to put obtained key via jungleflasher but nothing happens....is there some other way to put obtained key and do i need to spoof with original or 0272 firmware?

What was the original problem?,
*What dashboard is it currently on?*,
What is the error code?,
Why did you obtain the key by RGH and not dump the drive?,
Is the coolrunner still installed?,
This information is relevant if you want help...

 

[Buljo]

Thank you for your answer...i got replacement PCB, but problem is that i cannot put that obtained key from coolrunner on replacement PCB with Jungleflasher.
Is there another way to do that ?

---------- Post added at 09:40 ---------- Previous post was at 09:31 ----------

What was the original problem?------Some1 erased dvd drive before and i didnt make to find that modder or get any way to key
What dashboard is it currently on?----------I think that is on 2.0.13604.0 or 13599
What is the error code?---error code is 3151 351f b800 0601 c000 013e
Is the coolrunner still installed------i have removed Coolrunner after obtaining key

 

[crono1000]

You should be able to type your key manually in jungleflasher by clicking on the manual spoofing button... have you tried that already?

Sent from my LG-P999 using Tapatalk 2

 

[Buljo]

I tried Crono...It seems that key was lost during kamikaze or updating kamikaze mod....
I have copy-paste dvd key from j-runner log...It seems that is 9504 dvd drive and i have tried with jungleflasher...picked up some els 9504 dvd firmware,putting original 9504 and manually copy/paste obtained key...after that i was trying to update via usb stick but i didnt make to update....it is strange that i cannot save that firmware from jungleflasher cause it always save source firmware not manually spoofed firmware...before this console i was having few fat models with same problem but i have done that consoles without problem....I was trying to put 0272 firmware but it didnt help...

 

[Fisticuffs]

From your error code 3151= 12625 and 351f= 13599, I can't give you a definitive answer, I've not been in this situation before or read anything about it but..., Try putting 13146 dashboard update on a USB jump drive formatted to Fat32, Maybe you'll get lucky and reflash the drive so you can redump it, If not try 13599 update to see if you get out of the loop. Trial and error

Link----> Dash updates

 

[Buljo]

I will try tomorrow Fisticuffs and posted when im try...

 

[vrtclhykr]

That hex in the error code shows he is stuck on 13599. You need to stock your drive and then put 13599 on a stick to get out of the loop

 

[Buljo]

Thank you for your help,there is no update error anymore but there is another problem...when im putting that obtained key manually.in jungleflasher i getting authorizatrion and restore verify failed....obtained key is e064xxxxxxxxxxxxxxx but when i write it to drive it writes 0064xxxxxxxxxxxxxxxx....help

 

[Buljo]

I have tried to read that nand again and it seems that that obtained key is a key from console ,by serial number via jrunner it seems ok....is there a possibillity that some1 before me writed some other nand cause i cannot get that key to work?

 

[Fisticuffs]

Thank you for your help,there is no update error anymore but there is another problem...when im putting that obtained key manually.in jungleflasher i getting authorizatrion and restore verify failed....obtained key is e064xxxxxxxxxxxxxxx but when i write it to drive it writes 0064xxxxxxxxxxxxxxxx....help

I have tried to read that nand again and it seems that that obtained key is a key from console ,by serial number via jrunner it seems ok....is there a possibillity that some1 before me writed some other nand cause i cannot get that key to work?

Does the console play games?, Do you have the original nand dump still?

 

[Buljo]

Console doesnt play games like it was flashed with wrong key...i got what i think that was original files...:facepalm:

 

[Ticallion]

You will need to use Lizfix to inject the correct key into the 9504 firmware.

 

[Buljo]

obtained key is e064xxxxxxxxxxxxxxx but when i write it to drive it writes 0064xxxxxxxxxxxxxxxx---------is it problem in that maybe?

---------- Post added at 02:29 ---------- Previous post was at 02:27 ----------

Ticcalion i will try to use lizfix ....

 

[Buljo]

I tried....but problem is that i dont know anymore if that dvd drive is originally from that console and i presume its not....So RGH will be last option?

---------- Post added at 02:59 ---------- Previous post was at 02:57 ----------

Is there option that with Coolrunner dvd drive works? How?

 

[Ticallion]

I tried....but problem is that i dont know anymore if that dvd drive is originally from that console and i presume its not....So RGH will be last option?

You have already obtained your dvd key, therefore it stands to reason that you must also have your cpu key and nand dumps, correct?

Load the cpu key and nand into Jrunner, it will show what the OSIG is and the dvd key is for that console, whatever the dvd key shown there is, is what you will need to inject into the dvd drive in order for it to work with that console, providing the OSIG is for a 9504 drive. If not then RGH is your only option.