I have done these steps, I have loaded the ECC file I had yesterday. When I load up my XBOX 360 I get a black screen. No RRoD, Coolrunner has a red light with a green light that blinks.
[/QUOTE]
ANSWERED RGH QSB weird solder point?
- Thread starter tronix89
- Start date
- Status
I have done these steps, I have loaded the ECC file I had yesterday. When I load up my XBOX 360 I get a black screen. No RRoD, Coolrunner has a red light with a green light that blinks.
[/QUOTE]
Martin C
VIP Member
Front side (I have used a small wire for orange because the orange wire was to thick to fit on the pad).
http://i43.tinypic.com/1zccosm.jpg
Backside:
http://i43.tinypic.com/ol2md.jpg
This is my setting when I get the nand:
http://i44.tinypic.com/jahpwz.jpg
http://i43.tinypic.com/1zccosm.jpg
Backside:
http://i43.tinypic.com/ol2md.jpg
This is my setting when I get the nand:
http://i44.tinypic.com/jahpwz.jpg
So how do I fix this? Shall I just throw everything in the trashcan? I have managed to get a KV_enc file from the ECC file. But now I'm wondering why the console doesn't boot?
EDiT:
I'm now able to create ECC files with my DUMPS. I just checked some cables and now It works. I can now open the dumps with 360 Flash Tool Here is a screenshot:
http://i39.tinypic.com/5xrbqb.jpg
I wrote the new ECC file to the 360. I'm going to check out if Xell loads or not. Dammit, I get a black screen only. On the cool runner there is only 1 red light, no green.
EDiT:
I'm now able to create ECC files with my DUMPS. I just checked some cables and now It works. I can now open the dumps with 360 Flash Tool Here is a screenshot:
http://i39.tinypic.com/5xrbqb.jpg
I wrote the new ECC file to the 360. I'm going to check out if Xell loads or not. Dammit, I get a black screen only. On the cool runner there is only 1 red light, no green.
Last edited:
Martin C
VIP Member
No - go back to your other ECC image. The NAND image you've posted is not valid.
Why is your Coolrunner set to Slim?
Also, what's with the cap? it's not needed.
Pics are not enough to tell. You need a better pic of the underside. Do you not know how to take pics without them being blurry?
Why is your Coolrunner set to Slim?
Also, what's with the cap? it's not needed.
Pics are not enough to tell. You need a better pic of the underside. Do you not know how to take pics without them being blurry?
Here is the NAND file wich can make the ECC file:
http://www.mediafire.com/?f53lhd7394eb9c7
It's set on Phat, I have tested both when it didn't work.
I have removed the cap now.
Here is a better photo:
http://i39.tinypic.com/2uzqhy1.jpg
When I create ECC file i get:
When I turn my 360 on TV I get a RRoD with 3 lights. This is so frustrating.
http://www.mediafire.com/?f53lhd7394eb9c7
It's set on Phat, I have tested both when it didn't work.
I have removed the cap now.
Here is a better photo:
http://i39.tinypic.com/2uzqhy1.jpg
When I create ECC file i get:
When I write the ECC file I get:
The coolrunner is set on prog when I dump the NAND and write the ECC file. When I turn the 360 on my TV I set it to normal and disconnect the NANDX.
When I turn my 360 on TV I get a RRoD with 3 lights. This is so frustrating.
Last edited:
Martin C
VIP Member
I think you should stop.
Your original NAND was CB 5771. it says so right there in the zero pair data.
http://www.multiupload.com/PTJBS5OBIF
Download this ecc file and write to your console like so:
nandpro usb: +w16 image_000000.ecc
It's a valid CB5771 ECC file. See if it glitches with this.
Your original NAND was CB 5771. it says so right there in the zero pair data.
http://www.multiupload.com/PTJBS5OBIF
Download this ecc file and write to your console like so:
nandpro usb: +w16 image_000000.ecc
It's a valid CB5771 ECC file. See if it glitches with this.
Martin C
VIP Member
A little common sense wouldn't go amiss here.
I didn't put all the zeroes in. the proper filename is image_00000000.ecc, but surely you can see that as you have the file there.
I didn't put all the zeroes in. the proper filename is image_00000000.ecc, but surely you can see that as you have the file there.
I done that, I renamed the image to:
image.ecc
and in nandpro i write:
nandpro usb: +w16 image.ecc
and I get the couldnt read error.
-- edit --
I have written the ECC file via Jtag tool by coolshrimp, I could copy it. When I turn my 360 on there is one red light continiously on, and the green light is blinking. But there is no Xell, I have connected the 360 via HDMI. I think this crap can go in the garbage can :/. Is there an another way to get Xell on screen?
image.ecc
and in nandpro i write:
nandpro usb: +w16 image.ecc
and I get the couldnt read error.
-- edit --
I have written the ECC file via Jtag tool by coolshrimp, I could copy it. When I turn my 360 on there is one red light continiously on, and the green light is blinking. But there is no Xell, I have connected the 360 via HDMI. I think this crap can go in the garbage can :/. Is there an another way to get Xell on screen?
Last edited:
Martin C
VIP Member
Use the one I sent you.
You have to tell nandpro where the ecc file is - common sense really.
If this doesn't work, then send it to someone to do it for you. It's still salvageable.
Dude, I have used that one :\ why are you pretending as I did not :S I copied your file to my 360 via Jtag Tool:
NandPro v3.0a by Tiros
Looking for usb interface device
Flash Config: 0x01198010
Block Size: 16KB Block Limits: 0x000000..0x0003FF
File: ResetGlitch.ecc
Opt: Spare data will be initialized
Opt: Block markers will be initialized
Opt: Ecc will be re-calculated
Writing
004F
Press a key to continue
It just doesnt want to boot Xell, what ever I tried. I dunno if I really would send this piece of crap to some one to do it for me. I already have spend a lot of money on this crap, I cant spend more because I still have to pay my health insurrance.
NandPro v3.0a by Tiros
Looking for usb interface device
Flash Config: 0x01198010
Block Size: 16KB Block Limits: 0x000000..0x0003FF
File: ResetGlitch.ecc
Opt: Spare data will be initialized
Opt: Block markers will be initialized
Opt: Ecc will be re-calculated
Writing
004F
Press a key to continue
It just doesnt want to boot Xell, what ever I tried. I dunno if I really would send this piece of crap to some one to do it for me. I already have spend a lot of money on this crap, I cant spend more because I still have to pay my health insurrance.
Last edited:
Martin C
VIP Member
ok - so as it's still not glitching, you have two options.
1. Send to someone to fix.
2. Bin it.
1. Send to someone to fix.
2. Bin it.
Why are you giving him sh*t when he is trying to help you out? Deffinetly a case of PEBKAC.
Martin C
VIP Member
Lol, like the way you were telling me you still had the original NAND dump and you didn't, thus wasting a shedload of everyone's time?
Don't get me started.
Ah damnit, trow sh*t at you? Where the hell did I say something negative about fellow forum users here :\
Even if I send it to someone whoís going to do it for me, how do I know for sure that it will work.
In the last steps I copied the ECC file you uploaded, I said I was getting a green light on the coolrunner. It's annoying because this crap doesn't want to work, I spend 2 complete days on this useless crap. I'm very pissed off.
Don't get me wrong, English is not my native language and I suck with it. Sometimes I dont even have a clue what you try to say.
Even if I send it to someone whoís going to do it for me, how do I know for sure that it will work.
In the last steps I copied the ECC file you uploaded, I said I was getting a green light on the coolrunner. It's annoying because this crap doesn't want to work, I spend 2 complete days on this useless crap. I'm very pissed off.
Don't get me wrong, English is not my native language and I suck with it. Sometimes I dont even have a clue what you try to say.
Martin C
VIP Member
The 'stuff' works if
a. You can solder.
b. You can follow instructions.
c. You have a basic PC knowledge.
There's a very good chance that if you get this to someone, it'll work. Don't blame the Coolrunner - it's entirely dependant on the above three things. We cannot teach you this stuff and expect you to know how to do all three before even attempting it.
a. You can solder.
b. You can follow instructions.
c. You have a basic PC knowledge.
There's a very good chance that if you get this to someone, it'll work. Don't blame the Coolrunner - it's entirely dependant on the above three things. We cannot teach you this stuff and expect you to know how to do all three before even attempting it.
I know how to solder, I have been soldering for a couple years. The wires are good, have checked the solderjoints with a magnifying glass. The problemn with tutorials is there are so many, some people use like method 1 other 2. If you have never done it its easy to get confused. It's not like there is One Official tutorial or so.
I have tested it with HDMI and AV cable it just doesn't load.
I have basic PC knowlegde I used to crack software applications with debugger, code patchers, tackle file protectors like Armadillo, ASProtect, code keygens coding a file packer for my group.
As for the electronics, I do have the knowlegde I created many PCB's for working radio transmitters out from a scratch.
I think I messed this one up when I turned the 360 on without programming the coolrunner. As for following instructions, some people here on this forum just write stuff weird not everybody is good with advanced english, there fore I practise asian martial art I do know how to follow instructions.
It's just sad I wasted money on this 360 and it just doesn't want to work. I'm going to look futher on this forum, I might find something else I will lit it on fire
I have tested it with HDMI and AV cable it just doesn't load.
I have basic PC knowlegde I used to crack software applications with debugger, code patchers, tackle file protectors like Armadillo, ASProtect, code keygens coding a file packer for my group.
As for the electronics, I do have the knowlegde I created many PCB's for working radio transmitters out from a scratch.
I think I messed this one up when I turned the 360 on without programming the coolrunner. As for following instructions, some people here on this forum just write stuff weird not everybody is good with advanced english, there fore I practise asian martial art I do know how to follow instructions.
It's just sad I wasted money on this 360 and it just doesn't want to work. I'm going to look futher on this forum, I might find something else I will lit it on fire
Martin C
VIP Member
I asked for a close-up image of the CPU_PLL_BYPASS point which you never gave me. Can you take a clear pic and upload it?
- Status