reefz3ro
VIP Member
RGH Was working now no green light
- Thread starter Kr4k 4 J4Ck
- Start date
hmm what do you mean by pinched? and i burned the yellow wire a bit while taking the Nand-X wires off.
reefz3ro
VIP Member
well if a wire got pinched it could theoretically break the wire inside without breaking the plastic shielding you would need to test continuity to see
is the yellow wire bare where it was burned also if it is , is it touching anything
is the yellow wire bare where it was burned also if it is , is it touching anything
I took a picture of the wire here
And im not sure if i pinched any wires i cant really seem to test for continuity very well not really sure what im doing there.
Thanks.
reefz3ro
VIP Member
well i would flash the stock nand back set coolrunner to prog and see if it boots or you get RROD
Alright Flashed back the ORIGNAL nand and im getting RROD 3 lights 0110 So something isn't right with the Xbox
Considering i Just Reflowed the GPU it should work, applied pressure to the RAM chips when starting up and it didn't work.
So i thought back and, it was working perfectly outside the cage with the heat sinks placed on top, the second I put the heat sinks on it stops working.
Checked the heat sinks and they are off center about a couple Millimeters, and one is on top of a resister pressing on it, obviously not good, so i will take off the heatsinks and place them properly this time (lol) and i will post back results tomorrow.
http://xbox-experts.com/errorcode/E20/0110/
Last edited:
reefz3ro
VIP Member
well hopefully new thermal paste and reseating the heat sinks will fix it.
i have a Zephyr that glitches beautiful 5 sec every time till it got 0110 now it needs ram reflow/reball and im not sure its worth :/
i have a Zephyr that glitches beautiful 5 sec every time till it got 0110 now it needs ram reflow/reball and im not sure its worth :/
Yea im hoping its the Heat sinks cause all was working fine before i put it back together and its like ontop of a resistor and i had the screws pretty tight so i might need to replace the resister luckily but i have some spare boards around i should be able to do it.
reefz3ro
VIP Member
I had same issues with my cr, flashing back to stock no rrod, just no boot. After a head magnifier i found a broken trace, hard to solder so i'm gonna try a conductive pen to fix the trace. Hope that will work. I recommend to check traces around the solder points with a magnifier otherwise it might be a broken resistor. The multimeter on the ohm stand should give the nfo you need.
Booted the Xbox with Just the Xbox 360 and the 2 heat sinks on top made sure the GPU wasnt resting on the Resistor that it was on when i had it screwed in.
Booted fine no problems, next boot while it was on i bumped the GPU by accident and got RROD 0031.
So i relined the GPU and it booted again, got like 5 perfect boots in a row.
Going to put the Xbox back together and try again now.
Booted fine no problems, next boot while it was on i bumped the GPU by accident and got RROD 0031.
So i relined the GPU and it booted again, got like 5 perfect boots in a row.
Going to put the Xbox back together and try again now.
reefz3ro
VIP Member
All went well! forgot to post back earlier, the GPU Heat sink was ontop of a resistor so i moved it a bit started it up and it worked.
For the noisy fan i ripped out the metal lining in the top case part.
Wrote the ECC file again wrote the Flashed Nand, to the Xbox and it glitched!
Only problem i have that isn't really a problem, is that sometime after 3-4 boots in a row you have to unplug the Power cable and put it back in for it glitch. But i don't think my friend will mind that.
Thanks again for all the help everyone :biggrin:
Last edited: