hersheys247
VIP Member
RGH RGH2 Jasper 256 Wont Boot, and now RRoD! >_<
- Thread starter SOD_FrosT
- Start date
Northern Maine. Here's my latest JRunner log from trying to simply read my nand. Who knows, maybe my nand-x is fubar. Grrr.
Friday, June 08, 2012 10:26:10 AM
J-Runner v0.2 Beta (276) Started
Checking Files
Finished Checking Files
Downloaded *xeBuild/9199/bin/patches_falcon.bin
Downloaded *xeBuild/9199/bin/patches_jasper.bin
Downloaded *xeBuild/9199/bin/patches_xenon.bin
Downloaded *xeBuild/9199/bin/patches_zephyr.bin
Downloaded *xeBuild/9199/_jtag.ini
Finished Checking Files
Version: 03
Flash Config: 0x02001000
Unknown Flash Config found.
This may due to a new console type, bad soldering or hardware failure.
If it isnt the first check your soldering and reset your device.
You can always press ESC to cancel the read.
Error: 000 reading block 0
Error: 000 reading block 1
Error: 000 reading block 2
Error: 000 reading block 3
---------- Post added at 10:34 ---------- Previous post was at 10:28 ----------
This is super frustrating. Out of 2 JTag attempts, I got one. A Zephyr. Out of 2 RGH attempts, none. Both fubar. What the hell... I give up.
Lonewolf, looks like you're going to be getting a HUGE box. -_-
---------- Post added at 10:41 ---------- Previous post was at 10:34 ----------
Ok, I got it to fire back up with the CR Removed, DVD Tray Installed, but I still can't get a nand reading.
Friday, June 08, 2012 10:26:10 AM
J-Runner v0.2 Beta (276) Started
Checking Files
Finished Checking Files
Downloaded *xeBuild/9199/bin/patches_falcon.bin
Downloaded *xeBuild/9199/bin/patches_jasper.bin
Downloaded *xeBuild/9199/bin/patches_xenon.bin
Downloaded *xeBuild/9199/bin/patches_zephyr.bin
Downloaded *xeBuild/9199/_jtag.ini
Finished Checking Files
Version: 03
Flash Config: 0x02001000
Unknown Flash Config found.
This may due to a new console type, bad soldering or hardware failure.
If it isnt the first check your soldering and reset your device.
You can always press ESC to cancel the read.
Error: 000 reading block 0
Error: 000 reading block 1
Error: 000 reading block 2
Error: 000 reading block 3
---------- Post added at 10:34 ---------- Previous post was at 10:28 ----------
This is super frustrating. Out of 2 JTag attempts, I got one. A Zephyr. Out of 2 RGH attempts, none. Both fubar. What the hell... I give up.
Lonewolf, looks like you're going to be getting a HUGE box. -_-
---------- Post added at 10:41 ---------- Previous post was at 10:34 ----------
Ok, I got it to fire back up with the CR Removed, DVD Tray Installed, but I still can't get a nand reading.
Its not the NAND-X. Just did a dump of my JTag Zephyr and it worked. Identical dump as to what I had as a backup nand for it.
A bad flash config like that is a soldering issue, or potentially something done to standby clock/HANA area like Hersheys said. I believe four boards, carefully wrapped in bubble wrap, do fit in a large flat-rate :tongue: but still, the 16mb Jasper should be one you can get working yourself, it's down to soldering on the nand-x wiring I'm almost certain.
Ive got a super funny feeling your right about the nand-x wiring, especially considering my JTag Zephyr will read just fine and the jasper wont now. It did, untill I tried installing CR wiring... and now it's funky, mustve crossed something somehow. Grr!
Ive already got the large flat rate box, and I know the two falcons will fit, Im pretty sure I can get at least one of the jasper in there as well. The 16mb one is something I might be able to debug myself...
Ive already got the large flat rate box, and I know the two falcons will fit, Im pretty sure I can get at least one of the jasper in there as well. The 16mb one is something I might be able to debug myself...