RGH RGH2 Long booting time
- Thread starter WalangAlam
- Start date
- Mar 1, 2010
- 3,346
- 128
I stood it up :/
Not altered the wiring at all, it has been running with a usb hdd in - That's the only change apart from the consoles orientation.
Not altered the wiring at all, it has been running with a usb hdd in - That's the only change apart from the consoles orientation.
Ticallion
BANNED
512mb BB Jasper boots on average 30 seconds, using standard wiring config with CPU_RST on top of the board taped over fan shroud, using timing file A. 10ohm resistor in place too.
juanbrnt
VIP Member
i just want to share this with you guys i got a bb jasper and my time is 15 secs i put two ohms resistor and a cable similar as the blue but thicker i got it form a old usb cable , the routing all the same but ppint d i run it under the fan i hope this help some people and thanks again to tx
strange. My client too confirmed that by inserting two usb, he shortened his booting time to a minute and his shortened booting time is constant.
Problematic jaspers with RGH 1.0 glitch faster when you turn with remote controler. Try if you have one.
Sent from my IRC using Twitter
Sent from my IRC using Twitter
Been reading this thread with interest guys just done my 1st rgh2 jasper (bb) would not glitch with the resistor in sequence boots without it tho... I timed 10 of the boot sequences this is what i got (I left it powered down for 5 mins between it was laid flat) i got 43/15/1.09/20/52/25/40/1.09/36/4 going to try it standing up and maybe use low loss cable see if it has any effect as its just the standard coolrunner supplied cables all wiring above board except post_out 1 would like to get boot times down a little and maybe sell this going to try the usb hd inside looks like thats helped some of you guys anybody else noticed anymore quirks with there RGH boxes that maybe improved boot times 
edit = stood the console up and used hdmi lead as i was using component just got 10 under 20 second boots on the bounce crazy !
edit = stood the console up and used hdmi lead as i was using component just got 10 under 20 second boots on the bounce crazy !
Last edited:
just finished 256 bb jasper
10 ohm R and CR program with B (best results)
having 20-25 sec in average
best time is 10 sec
worse 65 sec (1 of 15-20 boots)
its reacts diffrent when all the gear (DVD,HDD,fan) is on
10 ohm R and CR program with B (best results)
having 20-25 sec in average
best time is 10 sec
worse 65 sec (1 of 15-20 boots)
its reacts diffrent when all the gear (DVD,HDD,fan) is on
The metal case alone changes drastically the boot time... here with file A without the case i get <40s boot tims
with the case, 2 to 3 minutes....
WIll try other files
with the case, 2 to 3 minutes....
WIll try other files
Last edited:
Ubergeek
Xecuter Groupie
Not at all, just a small percentage.
The entire tx beta team all have rgh2 boots 5 - 60 secs max.
Ubergeek
Xecuter Groupie
and are you using the double shielded lmr-100a cable (one end grounded) for cpu_rst as instructed ?
Speaking of, Uber, may want to start mentioning a good place to ground said cable..if I'm right pin five on the same header CPU_RST is soldered to is a ground at least on Xenon boards, I can't imagine it changing on the others.. I always ground on the motherboard side cause I have to cut the shielding off to fit through that hole by the southbridge, guess if you run it on the top side under the fan shroud you could still ground on the CR side... Any opinion on which routing is better or is it going to vary by console again?
Ubergeek
Xecuter Groupie
It's grounded exactly where the CoolRunner is grounded in my official guides
Routing is exactly like it is in my official guides (inc troubleshooting guides)
Routing is exactly like it is in my official guides (inc troubleshooting guides)
Yep, but didnt ground one end
Just tried XSFV B with normal wirewrap cable and no resistor
getting 5s to 40s max booting time (case, dvd, etc)
sthetix
VIP Member
on my falcon, connecting low loss cable shield to ground wont boot the console at all..Yep, but didnt ground one end
Just tried XSFV B with normal wirewrap cable and no resistor
getting 5s to 40s max booting time (case, dvd, etc)
trippy86
VIP Member
Ubergeek
Xecuter Groupie
You mean the actual CoolRunner installation instructions & trouble shooting guides that are stickies in the CoolRunner forums for the last 6 months?
Amazing.