RGH rgh2 on falcon help

[Lu the noob]

Hi I am 100% new to all of this but I did lots of reading before I got started. so I will give all the steps I have so far and tell you my problem any help will be greatly appreciated. so I dump the nand with home made LPT cable got 2 that marched used j-runner to program my cr3-lite I wrote the image_00000000.ecc to the I did the rgh2 set up on the cr3-lite I shorted LK1 set switch 1and 5 and on the other one I set the 2. so now at this point I connected the Xbox I got the xell screen I copied the keys to j-runner created the updflash.bin and put in in a fat32 USB flash drive. At this pint the cr3-lite the green light flashes with the red light on the Xbox goes on back the xell menu it reads the updflash.bin and it all goes good it tells me to shut it off and I do. Now here is where the problem is, after I shut it down I give it like a minute and I try to turn it on but the green light is not flashing and nothing comes up I have re done all the soldering like 4 times and it all works up to the point of it writing the updflash.bin after that the green glitch light does not turn on, please help the noob, thank you in advance for your help and kindness.

 

[AllyNerd]

There's an app for that
http://team-xecuter.com/forums/showthread.php?t=96474

 

[john mathews]

your not using any tx products we cant help 99 percent that cr3lite is fake

 

[Lu the noob]

tx product - cr3 lite

console - falcon

nand - 16mb

dash - 16202

cb - 5774

i dont know how to obtain the nand screen shot from j runner or the updflash

the xbox was working before

the green debug light does turn on before i put in the updflash

 

[Lu the noob]

tx product - cr3 lite

console - falcon

nand - 16mb

dash -
16202

cb - 5774

i dont know how to obtain the nand screen shot
from j runner or the updflash

the xbox was working before

the
green debug light does turn on before i put in the updflash

 

[AllyNerd]

If you press eject on the console what happens? Since it glitched into xell then everything should be good when you write your image. It would be best to use a jr programmer or nand x and jrunner because you can get different errors from using lpt homemade cable.

 

[Lu the noob]

if i push the eject the tray opens but the green light does not flash and the screen is blank

 

[Lu the noob]

its all good untill i write the image from the updflash.

 

[gavin_darkglide]

have you tried unplugging the power for 30sec after flashing the image?

 

[RayBray]

Could you please post the JR log

 

[N.E.Modz]

Could you please post the JR log

i would redo all your soldering mate, looks like a bird has just had a sh*t on your board. bet there is some cold solder joints somewhere.

 

[15432]

can you write the ecc image again and check does it work?

 

[Lu the noob]

i dont know how to get jrunner log i have the copy of the nand im just not sure how to make a log in j-runner. i will try to pull the power after i do the updflash see if that works.

 

[Lu the noob]

I wrote the ecc image again and it gets me to xell.

 

[15432]

fine. now build the RGH2 freeboot image and post JRunner logs here

 

[gavin_darkglide]

Just a side note, the fan shroud is a good idea, to insure maximum cooling. I lost a board waiting for it to glitch 1 time, because it wasnt getting proper airflow without it.

 

[Lu the noob]

sorry for my ignorance but im not sure how to build the rgh2 free boot. I loaded my nanddump1.bin and pressed creatXebuildimage. I got this





--------------------------------------------------------------
xeBuild v1.12.659
---------------------------------------------------------------
base path changed to C:\Users\me\Desktop\J-Runner\xeBuild
---- { Image Build Mode } ----
building glitch2 image
---------------------------------------------------------------
C:\Users\me\Desktop\J-Runner\043978482507\updflash.bin image built, info:
---------------------------------------------------------------
Kernel : 2.0.16747.0
Console : Falcon
NAND size : 16MiB
Build : Glitch (v2)
Xell : power on console with console eject button
Serial : 043978482507
ConsoleId : 016656382467
MoboSerial: 8578546100408257
Mfg Date : 06/18/2008
CPU Key : 324DA860CD6C40A506BE72ADFF4B9CC1
1BL Key : DD88AD0C9ED669E7B56794FB68563EFA
DVD Key : DF0293A22989596B336C8750C3AD954A
CF LDV : 11
KV type : type2 (hashed - unchecked, master key not available)
---------------------------------------------------------------
xeBuild Finished. Have a nice day.
---------------------------------------------------------------
Saved to C:\Users\me\Desktop\J-Runner\043978482507
Image is Ready

 

[Taijigamer2]

Congratulations, u'v just built a RGH2 nand for your console. load updflash.bin into source box and write to console. Then pull power lead out for 30 secs, re-insert and power on. Though I'm suprised the console is booting with that soldering, maybe tidy that up aswell.

 

[Lu the noob]

will try, as for the soldering quoting N.E.Modz “looks like a bird has just had a sh*t on your board.” I agree, since I am new at this I’m afraid if I do it over it will be worse.

 

[Lu the noob]

!!It worked!! it boots up now, thank you very much to all that gave me a hand with this I appreciate it very much.