RGH RROD 0022 after flash orgin nand

[changbom]

I had done with my RGH to get my DVD key from my xbox. So i try to flash back to orgin nand but i got 0022 error with 3 red light try to flash many time but got no succes. Now even i try to flash back to freestyle dash it did't work to. and for sure i remover RGH board before i flash back to orgin nand. Any one help me . the nand got 1 bad block. Did i had to remap it before flash it back

 

[The504]

What are you using to write the nand?

 

[changbom]

sure i'm using nand-x for flash my xbox

 

[seanr28]

I had done with my RGH to get my DVD key from my xbox. So i try to flash back to orgin nand but i got 0022 error with 3 red light try to flash many time but got no succes. Now even i try to flash back to freestyle dash it did't work to. and for sure i remover RGH board before i flash back to orgin nand. Any one help me . the nand got 1 bad block. Did i had to remap it before flash it back

this error is usually caused after you have shorted something near or on the green wire, check carefully using a magnifier if possible.

 

[mich_e_l2000]

i have the same error ....i removed all cabels and back to original nand but still RROD 0022....
the only error i did i used capicitor with value 220PF ( much less than what i have to use 68nf) between the GND and A to make it boot ...and really boot 2 times but hang in the first logo ...then 0022

is using capicitor 220pf harming the cpu ?????

 

[paul.86]

Me too got a zeyphr flashed ecc nothing come up on screen flashed orig nand and rrod 0022 flash ecc and it just keeps power light flashing

This is the same weather coolrunner installed or not orig nand dumped 4 times and compared I use this and rrod I flash ecc and it just keeps flashing with coolrunner or not.

with coolrunner keeps trying to glitch but I leave 10 15 mins and turn off tried vga av hdmi

I just want my cpu key arrrrrrggggghhhh

I have used microscope no shorts around green wire I have another board to compare with also

Thanks for everyone that helps

 

[Greator]

Its like more than 70% of people reflashing back original nand got this error.

I'm only want to extract Dvd key, How to return to original dash without 3rod 0022?

 

[jeppee]

I got the same problem with my another xbox. I'm really start thinking is it possible that the capacitor may have harmed xbox's hardware.

 

[lenselijer]

same problem here, got the dvdkey, flashed back original nand but now i get 0022 error.

any fix? i've removed all wires and soldering points are in perfect condition.

it's a 16mb jasper board

 

[dogeatdog]

Just a longshot, but I've retrieved about 5 dvdkeys from Falcons and Jaspers and flashed back to stock. Only difference is, I used a Matrix glitcher and an Olimex for this (and of course no QSB). Since I cannot imagine the Coolrunner could 'blow something up' and experienced people like lenselijers f-ing up the green spot, I can't help but thinking it might be the nandx ?

I always use nandpro 2.0e and an Olimex. You might try rewriting the stock nand with an Olimex if you can get your hands on one ? (lense, I'm in the NL, if you want me to take a shot at it...).

(yes, I use coolrunners for installations, but for getting keys I have 2 flashed Matrixes here).

 

[Greator]

I'm using matrix nand reader. still got rrod 0022. Is there some method to do this perfectly, like filename, when and how long to plug off power, version of nandpro used. I tried using nandpro3.0a but it keeps getting usb error -5 something from 0000 to 03ff.

 

[Xmarksthesh0t]

SEE MARTINS GUIDE

 

[esbmaepo]

Its like more than 70% of people reflashing back original nand got this error.

I'm only want to extract Dvd key, How to return to original dash without 3rod 0022?

Only reflash the first 50 blocks were xell is. Do not flash the intire original nand.

 

[LuGi]

Got the same error on a box but it didnt glitch as i hope (looong waiting time) so i removed the power and immediately added a cap to pll-gnd and after that the console didnt boot anymore.. so there was still some voltage on pll line and it screwed something..just my 5 cents.

 

[Greator]

SEE MARTINS GUIDE

Only reflash the first 50 blocks were xell is. Do not flash the intire original nand.

Flash the 50 blocks? Thats only 3mb, the whole nand is 16mb.
If you mean, "do not erase the nand", I already did that.

Someone should make a tutorial on how to get back retail dash after flashing xell without RROD 0022 error.

 

[esbmaepo]

Flash the 50 blocks? Thats only 3mb, the whole nand is 16mb.
If you mean, "do not erase the nand", I already did that.

Someone should make a tutorial on how to get back retail dash after flashing xell without RROD 0022 error.

XELL only resides in the first 50 blocks and leaves the rest untouched. So if you want to return to stock nand simply flash the first 50 blocks. This will overwrite xell.

It was a mistake to erase the entire nand but you should still be able to save your console, just follow MARTIN C's guide here:

http://team-xecuter.com/forums/showthread.php?t=77634

 

[Greator]

Sorry, I've tried this.

I have 6ff's and my LDV is also 6. And it still rrod 0022.

 

[esbmaepo]

Sorry, I've tried this.

I have 6ff's and my LDV is also 6. And it still rrod 0022.

So you can boot to xell now, AFTER you have erased NAND?

Is it a SLIM or PHAT?

 

[Greator]

I erased the nand, then write retail_image.bin (by multibuilder). goes rrod 0022.
write ecc. xell boots. its on jasper 16mb.

I know that you can write using xell, but here comes another problem. The xell cant read the xenon.elf file. It just stuck at [executing...].
I use usb with FAT format, just 2 files xenon.elf and nandflash.bin. Even use rawflash v4. I also tried Mupen64 also have same problem. I guess xell doesn't like my thumbdrive.

I hear that using LPT to write nand is much better than usb, is this true?

 

[esbmaepo]

I erased the nand, then write retail_image.bin (by multibuilder). goes rrod 0022.
write ecc. xell boots. its on jasper 16mb.

I know that you can write using xell, but here comes another problem. The xell cant read the xenon.elf file. It just stuck at [executing...].
I use usb with FAT format, just 2 files xenon.elf and nandflash.bin. Even use rawflash v4. I also tried Mupen64 also have same problem. I guess xell doesn't like my thumbdrive.

I hear that using LPT to write nand is much better than usb, is this true?

I dont believe that LPT should be better than USB. Never had any problem. I'm using Nand Flasher 360 for Windows with 360 Nandflasher from Maximus for reading/writing nand. Works perfectly.

Why not use Nandpro for writing Xell?

Still believe you have a LDV issue, try increasing value to 7