GENERAL rrod 0022 demon, coolrunner rev c

[skytecbvmo]

Hi all i have a problem maybe somebody can help thanks in advance!! jasper small block 16mb
1. updated dash to 14179
2.installed demon and cr rev c. see pics
3. dumped nand
4.create /write eec
5.boot xell and got cpu key no of f's (7)
^create and write glitched image both glitched and retail working fine!!
7.updated retail dash to current vers retail and glitch still working then i updated the demon side to current glitched dash now cr dont glitch no debug led no xell just rrod with 0022
ive tryed to rebuild changing ldv to 9 no luck any ideas pleaseView attachment 10484

View attachment 10485

View attachment 10486

View attachment 10487

View attachment 10488

 

[skytecbvmo]

some more pic's

 

[BL4K3Y]

Wow!

I suggest you have that sent to a pro to be repaired - that soldering is nowhere near acceptable enough, especially those QSB points on your DemoN!

 

[skytecbvmo]

Wow!

I suggest you have that sent to a pro to be repaired - that soldering is nowhere near acceptable enough, especially those QSB points on your DemoN!

ummm cheers m8 if thats the case why is is that they all check out against the nand as do all cables to be fair the whole lot did look a lot better but ive reflowed them a few times nands still read write fine ????? next odd comment plz

 

[LoneWolf913]

What image is giving you the RROD, retail or glitch? If you're getting RROD on the glitch image it wasn't built properly as no glitch nand will show an 0022 secondary error code. Post your J-Runner log please.

 

[Martin C]

ummm cheers m8 if thats the case why is is that they all check out against the nand as do all cables to be fair the whole lot did look a lot better but ive reflowed them a few times nands still read write fine ????? next odd comment plz

I wish RGH installs were merely a case of 'A gets soldered to B'. This ain't flat-pack furniture. You're working with electronics. I don't give a crap that it checks out now - poorly soldered joints will fail over time and most of those look like you've burned the flux out of them.

 

[skytecbvmo]

lol iv'e sent to a pro im just a give it a go sort ov guy you dont learn if you don't make mistakes.
Best ov it was i had it working and glitching in under 30 seconds demon was working well i have no idea ov what i done wrong in the end i would love to have finished what i started! But hey it's not quite in xbox heaven yet lol
But thanks for your input guys!!!

 

[BL4K3Y]

lol iv'e sent to a pro

While I'm flattered by that statement, I don't consider myself a pro - I'm more of a hobbyist.

However, I will clean up that soldering just to make sure it's tidy and hopefully get your box glitching again and get both retail and DemoN NANDs switching and booting as they should be .

 

[Martin C]

Ahhahahaha oh my goodness that is the fist time I seen someone that did a messy soldering job. Even the wires were burned.. Hahahahhaha

I can't wait 'til you're posting for help....

 

[skytecbvmo]

Ahhahahaha oh my goodness that is the fist time I seen someone that did a messy soldering job. Even the wires were burned.. Hahahahhaha

Iets see yours then wait till aid gets hold ov it then he can post some pics so what if the wires burnt there are still connected to the Right places. I beleave that this is a image problem and ya the wires need cleaning up but how they are worked i read the nands and dumped them! I've done my best but it aint in xbox heaven yet it can and will be fixed!!!! When u post yours they better be good cuz ill rip you so please keep silly comments to your self because i asked for help your comment was no help at all!! But thanks to those that tryed to help please leave this open so people can learn from my mistakes and maybe aid will show the end result !!! !