we should all work together and find a solution to this crappy issue seriously, rgh with fat consoles is good with me had no accidents like this before
RRoD 0022 with original dash, no green light on CR (or flashes once, very quickly)
- Thread starter GODZYLLA
- Start date
Have tried to unbridge that point and then flash the stock nand back to the nand? Bridging stops updates from flashing your nand and blowing the efuses. If your console was already updated to 13604 the fuses have been blown and the bridging of the U6T2 will cause more issues.
I have unbridged U6T2 since the incident, but Xell booted with the points bridged, and yes, the console was updated to latest dash since it came out.
with multimeter set to 20k ohm, i measure 9.55
i also have the 0022 problem, with 2 jasper boards now
Now it's worse, I only get max 3 kO (disconnected the green wire)
And another thing... when i test the R7R17 I get a solid reading, but I think if I lower the pin head of the meter to a lower point (imagine the resitor's "leg" is above the circuit... I really don't know how to explain) I get nothing. Also, if I test the PLL point with the other end of the resistor, shouldn't I get the resistance? (same thing on buzzer, it shows pll and closest point of the res connected, but on the other end no reading...)
And another thing... when i test the R7R17 I get a solid reading, but I think if I lower the pin head of the meter to a lower point (imagine the resitor's "leg" is above the circuit... I really don't know how to explain) I get nothing. Also, if I test the PLL point with the other end of the resistor, shouldn't I get the resistance? (same thing on buzzer, it shows pll and closest point of the res connected, but on the other end no reading...)
I solved my 3 ROD problems and freeboot boot
I have japser 256/512
Write ORG nand and 3 red 0022 lights then
Write ecc image by +w16(I know that I have 256/512 nand)
Write glitch image by -w256
It works OK but sometimes start animation is freez or NXE Dash can freez after (30-60 sek)
when i Launch xexmenu or dashlaunch console work perfect so i set dashlaunch and when console didn't freez on start animation it works ok (1 about 5 times)
Any suggestions for this freez?
Hi
I have japser 256/512
Write ORG nand and 3 red 0022 lights then
Write ecc image by +w16(I know that I have 256/512 nand)
Write glitch image by -w256
It works OK but sometimes start animation is freez or NXE Dash can freez after (30-60 sek)
when i Launch xexmenu or dashlaunch console work perfect so i set dashlaunch and when console didn't freez on start animation it works ok (1 about 5 times)
Any suggestions for this freez?
Hi
Last edited:
That's the command I use... but if I say I used +w16 on the entire nand and after that I flashed with -w16, is that ok?
Anyone with this problem tried to flash with nandpro 2.0?
Anyone with this problem tried to flash with nandpro 2.0?
That's possible... and I'm afraid not to f**k it up more by "tweaking" various hardware settings.
Maybe build yourself a clean nand. Of course you need your cpu key for that.
You never know....:rolleyes2:
I built a retail 13604 with multi builder 0.3 (maybe with 0.4 too, don't remember)... no success.
Green wire removed.
CR removed.
Nand wires removed.
1-2 bridged
3-6 = zero
3-5 = aprox 3 ko
3-4 = aprox 10 ko
3-8 = aprox 3 ko
7-8 = aprox 5 ko
CR removed.
Nand wires removed.
1-2 bridged
3-6 = zero
3-5 = aprox 3 ko
3-4 = aprox 10 ko
3-8 = aprox 3 ko
7-8 = aprox 5 ko
I also have the problem, BB Jasper with 0022, I haven't written the nand at all, only read it. I just connected the coolrunner and tried to boot retail and 0022, I desolder everything=0022. So right now I'm stuck with nothing attached and 0022...
i am stuck here too, hope someone knows how we can solve this issue
loads of 0022 messed up dont knw why
loads of 0022 messed up dont knw why
I thought I lifted PLL point, but since I can get a solid reading betwen pll and the one under the heatsink (even scraped the trace a bit just to be sure) I think it's fine.
With the solder bridge "disabled" (or so I think it is) I can't get a reading between point 3 and point 1 (the resistor may be lifted at point 2?), between 3 and 5 I get 3ko, and between 3 and 4 10ko, so it's same as above.
Does it matter if points 1 and 2 are brigded, because from what I read they're in series?
With the solder bridge "disabled" (or so I think it is) I can't get a reading between point 3 and point 1 (the resistor may be lifted at point 2?), between 3 and 5 I get 3ko, and between 3 and 4 10ko, so it's same as above.
Does it matter if points 1 and 2 are brigded, because from what I read they're in series?