JTAG RROD Jtag 0020

[Road-Runner]

Ok i recived 2 rrod in the mail yesterday and one had 0102 and the jtag had 0020 i reflowed both and put a rrod kit in them both but it fixed the 0102 rrod with is a xenon and the 0020 is a xenon to but i dont know what i have to do to fix the 0020. when i looked at the jtag wires some was touching to i unslodered them and did them correct but that didnt fix the rrod.

i went to http://www.llamma.com/xbox360/repair/Xbox-360-error-codes.htm and i looked up the 0020 code and it says 0020 (Not yet known, possibly overheating)

So can anybody tell me what to do to fix it or why its red ringing?

 

[WNYConsoles]

0020 is general hardware failure so either the chip is dead, bridged solder join, etc OR the NAND image is bad. Wires loose on a JTAG would generally cause E79.

How are you reflowing the boards?

 

[Road-Runner]

0020 is general hardware failure so either the chip is dead, bridged solder join, etc OR the NAND image is bad. Wires loose on a JTAG would generally cause E79.

How are you reflowing the boards?

I have a reflow station... so do i need to check the jtag wires or what?

 

[WNYConsoles]

JTAG re-wire on the Xenon wouldn't be a bad idea just to make sure but as I said, Xenon usually throws E79 if wiring is bad with FB installed.

The Xenon was 0020 when you got it and after reflow it was still 0020? Did you try a 2nd reflow?

 

[Road-Runner]

so should i just unslodered all the jtag wires then see if its still rrod and if it is then i know that thats not my problem?

 

[Road-Runner]

does anybody els kno any els things i can do to fix this?

 

[BL4K3Y]

Did you de-solder the wiring and flash the stock NAND back?

If the console still RRODs with the stock NAND then it is more likely to be a hardware fault which will mean you need to have the console re-flowed or even better, re-balled.

 

[Road-Runner]

Did you de-solder the wiring and flash the stock NAND back?

If the console still RRODs with the stock NAND then it is more likely to be a hardware fault which will mean you need to have the console re-flowed or even better, re-balled.

i done reflowed it but idk if it has stock nand on it because i got it rrod but what should i do.? should i dumo the nand and do what next? thats why i posted in the noob section

 

[BL4K3Y]

Dump the NAND and open it in 360 Flash Dump Tool.

If it is stock, you will see Retail or XBR/FreeBOOT if it is hacked.

 

[Road-Runner]

Dump the NAND and open it in 360 Flash Dump Tool.

If it is stock, you will see Retail or XBR/FreeBOOT if it is hacked.

ohk thanks ill do that later and let you know what it is... but the jtag a sh*tty solder points and solder was on other points on the board but the person i got it from said he got it from buckeye..

 

[BL4K3Y]

Can you post some images of his "handy work"?

 

[Road-Runner]

Can you post some images of his "handy work"?

i dont have a really good camera but i will do my best to post pictures but i took some soldering off that he messed up.

 

[cj_goalie31]

0020 could be anything from a blown chip to a cut trace or a bridged connection just look over the board and make sure there is no components missing, damaged traces, etc.

 

[Road-Runner]

0020 could be anything from a blown chip to a cut trace or a bridged connection just look over the board and make sure there is no components missing, damaged traces, etc.

yes ill post a picture of when buckeye jtaged it on his bad soldering but i tried to fix it upp a bit

 

[dirtyscout]

if its a jatg i had a customer try and update from a freeboot nanddump and flashed back a bad nand and it 0020. he never had a good nand dump and it was done for..