SATA Chipset
- Thread starter johnjohn
- Start date
does your mobo have on board graphics because if it doesnt then you should be able to get some info from ati.com as you have some sort of ati chip on your motherboard.
sorry for the bump, but i finally found my motherboard on the hp website.
http://h10025.www1.hp.com/ewfrf/wc/document?docname=c00496280&lc=en&cc=us&dlc=en&product=1843604&lang=en#N362
its says the southbridge is SB400 and thats what it says on the ATI chip nest to the SATA connectors
http://h10025.www1.hp.com/ewfrf/wc/document?docname=c00496280&lc=en&cc=us&dlc=en&product=1843604&lang=en#N362
its says the southbridge is SB400 and thats what it says on the ATI chip nest to the SATA connectors
got same problem m8, i have a dual core with to sata slots
is my motherbroad compatible with the sammy hard drive
motherbroad is aliveNf4g-dvi
chipset - northbridge nviadia - geforce 6100
southbrigde - nvidia - nforce 410 mcp
2 serial sataII connectors
get this in Xtreme Boot Maker
I have a ms 25 and an NVIDIA nForce 430/410 Serial ATA controller. I downloaded the xtreme 5.2 firmware and formatted my flash drive to use the xtrem52a. All goes fine and i reboot my computer, set it to boot from the flash drive, then reboot my computer and xbox second. When i get to the dos screen i have typed in xRead xxxxxxx xxxx. After i type them in a few options appear which say xtrem master or xtrem slave i have tried them both in just about every port and it just starts blinking green then stalls. When i hit escape i get this message 'status=00 should be 70'. A have searched the net high and low and can not find an explanation for this. Maybe i have to edit my hex or something but i do not have any idea how or to read the codes. Someone please help me ive tried everything. Should I just buy a PCI Controller Card VIA VT6421A, or is this onboard SATA going to work?
Thank you,
is my motherbroad compatible with the sammy hard drive
motherbroad is aliveNf4g-dvi
chipset - northbridge nviadia - geforce 6100
southbrigde - nvidia - nforce 410 mcp
2 serial sataII connectors
get this in Xtreme Boot Maker
I have a ms 25 and an NVIDIA nForce 430/410 Serial ATA controller. I downloaded the xtreme 5.2 firmware and formatted my flash drive to use the xtrem52a. All goes fine and i reboot my computer, set it to boot from the flash drive, then reboot my computer and xbox second. When i get to the dos screen i have typed in xRead xxxxxxx xxxx. After i type them in a few options appear which say xtrem master or xtrem slave i have tried them both in just about every port and it just starts blinking green then stalls. When i hit escape i get this message 'status=00 should be 70'. A have searched the net high and low and can not find an explanation for this. Maybe i have to edit my hex or something but i do not have any idea how or to read the codes. Someone please help me ive tried everything. Should I just buy a PCI Controller Card VIA VT6421A, or is this onboard SATA going to work?
Thank you,
I have a ms 28 and an NVIDIA nForce 430/410 Serial ATA controller. I downloaded the xtreme 5.3 firmware and formatted my flash drive to use the xtrem53a. All goes fine and i reboot my computer, set it to boot from the flash drive, then reboot my computer and xbox second. When i get to the dos screen i have typed in xRead xxxxxxx xxxx. After i type them in a few options appear which say xtrem master or xtrem slave i have tried them both and it just starts blinking. Can someone please let me know if my chipset will work. I also have the Blaster 360. :?:
you need a VIA chipset to flash a samsung ms28, unless you use the VCC method and you have a high chance of screwing up your drive if you do that.
i have decided to buy this, http://cgi.ebay.co.uk/ws/eBayISAPI.dll?ViewItem&ih=003&sspagename=STRK%3AMEWA%3AIT&viewitem=&item=130111982150&rd=1&rd=1 any good?