ANSWERED SLIM: Flashed stock nand back. Got error 0022

[lil BLu3 SMuRF]

Well, I have the CoolRunner installed. I was able to play retail before on it stock nand. Then I flashed it to RGH nand. Ok all-in-all everything worked. Then I flashed the stock nand back to it. Got a red light and secondary error of 0022. My soldering is good because it booted before and I just re-flashed the glitch_image back to it and it booted.

So how do I get the retail back on it? I already tried flashing the original nand and it did what I said above.

 

[BL4K3Y]

You need to disable/remove your CoolRunner chip so that the console can boot in it's retail state.

 

[lil BLu3 SMuRF]

You need to disable/remove your CoolRunner chip so that the console can boot in it's retail state.

But it worked before when the CR was installed... But then again the CoolRunner wasn't programmed...


#fcuk

How do you disable it without un-soldering anything? Could I just erase it?

 

[BL4K3Y]

I believe you can just de-solder the 3.3V and GND wires but I would recommend removing it completely if you intend to keep the console at it's retail state.

 

[lil BLu3 SMuRF]

I believe you can just de-solder the 3.3V and GND wires but I would recommend removing it completely if you intend to keep the console at it's retail state.

I'm just putting it into retail state momentarily. So I'll just unsolder those 2.

 

[x360ccm]

wouldnt flickin the switch to program disable it.

 

[lil BLu3 SMuRF]

wouldnt flickin the switch to program disable it.

I thought the same but no.

 

[Martin C]

How long does it take to RRoD?

 

[lil BLu3 SMuRF]

Alright that's weird... I just desoldered the 2 wires, GND and 3v, and it still gave me the same error. The coolrunner has no power so I don't see how it would work.

---------- Post added at 13:57 ---------- Previous post was at 13:56 ----------

How long does it take to RRoD?

About 25 seconds after touch of power button

 

[Martin C]

And is this image definitely the last one you used on your console? IE you've not updated it in between?

Check my LDV sticky.

 

[lil BLu3 SMuRF]

And is this image definitely the last one you used on your console? IE you've not updated it in between?

Check my LDV sticky.

Damn I'm a dumbass. On the way of checking the 7BL key on 360 flash tool, I was thinking "watch it be 13599 and not 14699...
Well it was 13599... So that's the problem...

/facepalm :facepalm::facepalm::facepalm:

 

[Martin C]

No worries - boot to XeLL, get the right LDV and build a new retail NAND in Multi_Builder.

 

[lil BLu3 SMuRF]

No worries - boot to XeLL, get the right LDV and build a new retail NAND in Multi_Builder.

Thanks!

 

[lil BLu3 SMuRF]

One more question though... I have 4 f's... That means I have an LDV of 4 right?

Ok, so how would I go about building my new retail nand image of 4 LDV?

 

[Martin C]

One more question though... I have 4 f's... That means I have an LDV of 4 right?

Ok, so how would I go about building my new retail nand image of 4 LDV?

It's all in my LDV sticky!