SLIM PROTO INSTAL

[ferdoo]

HI guis, i instal the slim proto firts time. But i cant boot. I have used the DGX for key extraction with suckess boot xell ok.
The proto chip is not working. have someone idea pls?
I try many settings and i have read the SLIM PROTO - Installation & Tuning Guide from ubergeek

i thy unsolder the resistor unbridged R2C4, R2C6, R2C7 that i need bridged for nand read/write. No look yet.

TX-Products used : J-R-Programmer V2 ; Slim Proto ; Corona Postfix Adapter V2
Console : Corona V3
Nand : 16MB
Dashboard : 16203
CB :13121

LOG:
===================================================
7. decembra 2013 15:13:54


J-Runner v0.3 Beta (4) Started






Checking Files
Finished Checking Files
Version: 03
Flash Config: 0x00043000
00043000
Corona
CB Version: 13181
Corona
Reading Nand to D:\XXXBOXXX\J-Runner\output\nanddump1.bin
Reading Nand
Done!
in 2:12 min:sec


Reading Nand to D:\XXXBOXXX\J-Runner\output\nanddump2.bin
Initializing nanddump1.bin..
Corona
Reading Nand
RGH2 Selected
Nand Initialization Finished
Done!
in 2:12 min:sec


Comparing...
Nands are the same
Corona Manually Selected
Version: 03
Flash Config: 0x00043000
Writing Nand
CORONA_16MB_DGXv2.ecc
Done!
in 0:11 min:sec


Corona Manually Selected
Version: 03
Flash Config: 0x00043000
Writing Nand
CORONA_16MB_DGX.ecc
Done!
in 0:11 min:sec


Corona Manually Selected
Version: 03
Flash Config: 0x00043000
Writing Nand
CORONA_16MB_DGXv2.ecc
Done!
in 0:11 min:sec


Getting info from ip 192.168.0.103...
LockDownValue is 2
Initializing nanddump1.bin..
Corona
Nand Initialization Finished
Getting info from ip 192.168.0.103...
LockDownValue is 2
Initializing nanddump1.bin..
CpuKey is Correct
Added Key to Database
Corona
Nand Initialization Finished
Moving All files from output folder to D:\XXXBOXXX\J-Runner\165704524443
Load Files Initiliazation Finished
16537
Started Creation of the 16537 xebuild image
KV Info saved to file
---------------------------------------------------------------
xeBuild v1.09.639
---------------------------------------------------------------
base path changed to D:\XXXBOXXX\J-Runner\xeBuild
---- { Image Build Mode } ----
building glitch2 image


---------------------------------------------------------------
D:\XXXBOXXX\J-Runner\165704524443\updflash.bin image built, info:
---------------------------------------------------------------
Kernel : 2.0.16537.0
Console : Corona
NAND size : 16MiB
Build : Glitch (v2)
Xell : power on console with console eject button
Serial : 165704524443
ConsoleId : 030740158873
MoboSerial: 7501253122842425
Mfg Date : 11/01/2012
CPU Key : A505A429F56A----------D157C4A7B26
1BL Key : DD88AD0C9ED6-------6794FB68563EFA
DVD Key : 787D9F2B616A1-----38BA49ED1B53EB7
CF LDV : 2
KV type : type2 (hashed - unchecked, master key not available)
---------------------------------------------------------------
xeBuild Finished. Have a nice day.
---------------------------------------------------------------
Saved to D:\XXXBOXXX\J-Runner\165704524443
Image is Ready
Initializing updflash.bin..
Corona
Nand Initialization Finished
Version: 03
Flash Config: 0x00043000
Writing Nand
updflash.bin
Done!
in 2:10 min:sec

 

[ferdoo]

and i dont hear ticking meybe not normal,,, i mean that the post fix is no good instaled bud with the DGX is bootet fine.......

 

[Antalpromille]

You need to bridge those points again, and try 10cm cpu_rst, 12cm post out and dip 3 or 4.

 

[ferdoo]

You need to bridge those points again, and try 10cm cpu_rst, 12cm post out and dip 3 or 4.

Yes i have this try but no luck,,

 

[TX_F1ERCE_TX]

Is the debug light blinking every 5 seconds?

 

[Antalpromille]

Yes i have this try but no luck,,

Have you re-bridged R2C6 and R2C7 that you unbridged? Without them it wont work.

 

[ferdoo]

yes i have re-bridged R2C6 and R2C7 and R2C4 too but no luck ,, the green light blink evry 5 s,, but i dont hear ticking from the fan....

 

[ferdoo]

I have try other PROTO chip and DGX but its the same no luck,,, somting is wrong

 

[Antalpromille]

yes i have re-bridged R2C6 and R2C7 and R2C4 too but no luck ,, the green light blink evry 5 s,, but i dont hear ticking from the fan....

What lenght is your cables? Have you tried all dips?

 

[ferdoo]

i have 10cm CPU_RST connected to cpurest point on qsb ,,, and 5cm post out connected to 120 point on post fix ( i have try 5,50,70,90) no luck

DIP settings i have 8 on for corona and try 4 , 3, 3+4, 4+5, or all off

i have no ida

the post fix must be good instaled i have become the xell with DGX ......

 

[Antalpromille]

Try 12cm wire to regular post pad. I have done 4 coronas this week with the proto and all of them booted almost instant with 10cm cpu_rst and 12cm post_out1 with dip 3 or 4.

 

[ferdoo]

ok i try 12cm wire to regular post pad after i post the result, thanks for help Antalpromille

 

[ferdoo]

i have try but still no luck,, but now i hear the fan slows when glitching the green led get on

 

[Antalpromille]

i have try but still no luck,, but now i hear the fan slows when glitching the green led get on

Wierd, i never had any issues with my slim protos.

Edit: add new pictures of your actuall install as it is now.

 

[ferdoo]

I try now restore nand backup and boot original nand ....

 

[ferdoo]

I try now restore nand backup and boot original nand ....

The console started normal with original nand its wierd
i have try disconect the post out then started console but the green led not blink also the post fix adapter must be good instaled

 

[Antalpromille]

The console started normal with original nand its wierd
i have try disconect the post out then started console but the green led not blink also the post fix adapter must be good instaled

What resistance do you get between 5 and GND with the wire disconnected?

 

[ferdoo]

What resistance do you get between 5 and GND with the wire disconnected?

i measure 4,5M ohm ,,,, what with this ?

 

[Antalpromille]

4.5 Mega Ohm is way to high! Should be somewhere between 60k Ohm and 200k Ohm. Try reseating the post fix adapter and se if youget a better reading.

 

[ferdoo]

4.5 Mega Ohm is way to high! Should be somewhere between 60k Ohm and 200k Ohm. Try reseating the post fix adapter and se if youget a better reading.

i dont known how sold i right maesure i have put + on 5V and - on GND and i can not measure the value its groving and decreasing .....