slim proto v2 no green debug light??

[vsjsmmks]

TX Product(s) used: Slim proto v2, 4g R/W kit, post fit adapter v2, post QSB
Console Type: corona
NAND size: 4GB
Dashboard version: 16547
CB version:
Screenshot of NAND details from J-Runner:
H:\
Reading from H:\ to C:\Users\Victorino\Desktop\J-Runner\output\nanddump1.bin
Done!
in 0:03 min:sec
Initializing nanddump1.bin..
Corona 4GB
RGH2 Selected
Nand Initialization Finished
H:\
Reading from H:\ to C:\Users\Victorino\Desktop\J-Runner\output\nanddump2.bin
Done!
in 0:03 min:sec
Comparing...
Can't check for bad blocks. No Spare data. Possibly Corona 4GB
Can't check for bad blocks. No Spare data. Possibly Corona 4GB
Nands are the same
ECC created
Use Edited Options Selected
ECC created
Writing to H:\ from C:\Users\Victorino\Desktop\J-Runner\output\image_00000000.ecc
Done!
in 0:00:279 min:sec:ms
Initializing nanddump1.bin..
Corona 4GB
Nand Initialization Finished

J-Runner log:
updflash.bin log (if applicable):
Image of Coolrunner:



Description of problem: no green debug light, with varies dips set from suggestions slim proto v1/v2 install guide

Was the console working before you started: Y

Do you get a green debug light appear on the RGH chip every 4-5 seconds:n

How long is the light on for each time: never

 

[playingmax]

all dips look like they are on. keep 8 and 3 on rest off. if that doesnt work try 8 and 4 on. on so on. 8 has to been on for corona.

 

[playingmax]

http://team-xecuter.com/forums/showthread.php?t=139308

 

[vsjsmmks]

I tried all settings that was a shot after install before setting dips, it should flash green even if dips are incorrect, correct??

 

[Blagus]

Recheck CPU_RST solder point, make sure it's really soldered to QSB. Same thing with Postfix adapter, try to remove it and reinstall. Use enough flux to make sure it's really soldered.
Also, try direct Post_1 point on postfix QSB.

 

[playingmax]

did u test ur postout w/ multimeter? and post pic of cpu rst.

 

[vsjsmmks]

ok, is there a thread to show how to test with mulitmeter

 

[vsjsmmks]

 

[Blagus]

I guess playingmax was thinking of the actual CPU_RST point on board that you soldered to.

 

[playingmax]

I guess playingmax was thinking of the actual CPU_RST point on board that you soldered to.

thank you.

and vsjsmmks u should use the double shielded cable that came w/ the kid.

 

[vsjsmmks]

just resoldered, it might have been loose, ill give it a try! I do have cable, but I didn't use it on last rgh and work great! push comes to shove ill give that a try too!

 

[playingmax]

View attachment 24727 just resoldered, it might have been loose, ill give it a try! I do have cable, but I didn't use it on last rgh and work great! push comes to shove ill give that a try too!

give it a try n report back. good luck.

 

[gazcoigne]

in my experience the shielded cable never yields better results always worse

 

[vsjsmmks]

the blue screen of success!! thanks guys!!

 

[playingmax]

the blue screen of success!! thanks guys!!

congrats! let everyone know who u got it working. could help out others. Oh, dont forget to hit the thanks