ANSWERED Slim-Un-Lock command returned an error

Deleted TX Member · Jan 12, 2012

I've made a thread about this a while ago here:
http://team-xecuter.com/forums/showthread.php?t=76804

I've been told that the x360USB Pro would solve the problem, so I ordered it. Only got it yesterday.
As I said on the previous thread - I have a DG-16D4S FW 0272 (labeled 9504) flashed with lt+ 1.90. I didn't flash it, I paid to a store to flash it for me.
I updated the firmware and installed all the drivers for the x360usb. Then I connected the drive to the computer with the x360usb (using Xbox to power the drive on), started the flashing process and the same thing happened..
I followed the tutorial, method A (Dump the original Firmware from the drive), it said:

Now select Slim Unlock
Jungleflasher will unlock the drive and place it into Vendor Mode

So I clicked Slim Unlock on JF and got an error saying "Slim-Un-Lock command returned an error". After I clicked OK another error showed up saying "Unlock Failed !".
I then tried method B (Use SlimKey), which said:

Then select SlimKey Button
You will be faced with Jungleflasher asking if you want to send Unlock to slim – click YES

So that's what I did. After clicking YES, I got the same error as before: "Slim-Un-Lock command returned an error", then "Unlock Failed !" and then "SlimKey failed!".

As I said before, my drive has been flashed to 1.9 by a store, and I think it has been unlocked using the kamikaze hack.

Here's the log file:
http://www.mediafire.com/?9liojtay5jy95z8

peterrepek · Jan 12, 2012

You can check if is realy the Kamikaze Hack?
Open the DVD and on your winbond chip you will notice a little hole.

doe1200 · Jan 12, 2012

if your drive has been unlocked with the Kamikaze Hack you need to send the unlock command in jungleflasher then rub the hole on the chip with a bit off alcohol on a qtip you will here jungleflasher beep and the spi status change to 0x00 then the drive will be in vendor mode and you can write to it

Deleted TX Member · Jan 12, 2012

Yeah there's a hole.
And what kind of alcohol?

btw, I think I miss-followed the tutorial at the beginning, I now got to a different part, saying to use slimkey and click no afterwards, after doing so I got many files: "Dummy.bin" "Identify.bin" "Inquiry.bin" "Key.bin" "Serial.bin".
I then followed and followed and got to the unlocking part, it said to click "Intro / Device ID Button", and to click the "Spi Status Button" once in vendor mode. but the "Spi Status Button" is not clickable for me..
I then just clicked "Outro / ATA Reset" to get out of vendor mode and closed JF and the Xbox.
Screenshot:

Log:
http://www.mediafire.com/?8sesxcmvvbedhe4

doe1200 · Jan 12, 2012

have dummy bin only and usb only ticked in jungleflasher slimkey is used to get your dummy bin try to intro device id then power cycle then try to press the spi status button you will get a message clic ok then rub a bit of isopropanol on a qtip on the hole. jungleflasher should beep then spi status should change to 0x00

doe1200 · Jan 12, 2012

are if you get into vendor mode like your pic try to lock the drive by pressing ctrl/alt and f11 to see it will bring the spi status to 0x80c

Deleted TX Member · Jan 12, 2012

I did it but I can't click the spi status button since it's grayed out.
look at the image in my previous post.

doe1200 · Jan 12, 2012

yes i see that but you need usb only ticked when its greyed out did you try CTRL ALT F11 just seen your jf log spi status is 0x0c you need to try and lock it

Deleted TX Member · Jan 12, 2012

Nothing happens when I press ctrl alt f11.

---------- Post added at 17:26 ---------- Previous post was at 17:22 ----------

I just did a quick google search, seems like its ctrl SHIFT f11.
I pressed those and a line showed up on the log saying "Spi Status: 0x8C", but the button is still grayed out.

doe1200 · Jan 12, 2012

yes sorry bout that shift now it will lock and you will be able to unlock it now yeah ctrl shift f11 my mistake havent used that command in a while

Deleted TX Member · Jan 12, 2012

Ok, I now tried to outro and then intro, and the spi status became clickable.
I clicked it, then clicked yes, the dots started showing up so I rubbed the hole with the qtip (which had alcohol on it), and nothing happened.

doe1200 · Jan 12, 2012

keep rubbing till you hear it beep and spi change is it rubbing alcohol like isopropanol you are using

jaycboy · Jan 12, 2012

RafiAccount said:
Ok, I now tried to outro and then intro, and the spi status became clickable.
I clicked it, then clicked yes, the dots started showing up so I rubbed the hole with the qtip (which had alcohol on it), and nothing happened.

keep rubbing i sometimes have to restart jungle flasher and unplug everything if it fails first time then just re do the process till i get the magic beep..and i use my finger tip tbh

Deleted TX Member · Jan 12, 2012

I've been rubbing it for a few minutes..
Also I just noticed something:
on the tut it says that after clicking the spi status button a message saying "Spi Status Register is S/W protect", but I got a message saying "Spi Status Register is H/W protect".
Could it be the reason?

jaycboy · Jan 12, 2012

try the to probe resistor way if your not getting any joy and like i say close jungleflasher and pull out usb and replug and reload everything after a failed attempt....e.g. no beep if youre getting the dots apear its sending the unlock pulse thats wen u probe or rub lol

Deleted TX Member · Jan 12, 2012

I will try to use 3.3v +100 Ω wire tomorrow.. My uncle will bring me the tools.
btw, here's the log of my last try (with alcohol) - idk might help:
http://www.mediafire.com/?48ebslvedqh353o

peterrepek · Jan 12, 2012

Be sure what you are doing with the 3.3V and 100ohm resistor.

Did you try to restart your computer and remake all from the begining?

Deleted TX Member · Jan 14, 2012

I tried the 100 ohm method, it worked.
Now, according to the tutorial I need to "Read" the original firmware, so I clicked the "Read" and nothing happened, I got this on the log:

Sending Device ID request to port 0x0000
Spi Status: 0x8C
Manufacturer ID: 0xEF
Device ID: 0x11
Flash Name: Winbond/NEX(W25P20/NX25P20)
Flash Size: 262144 bytes

Sending Spi UnLock request to Port 0x0000
...................................................................................................................................................................................................................................................................................................................................................................................
Spi Status: 0x00

Getting Status from port 0x0000
Invalid Status 0x0

What do I do?

Deleted TX Member · Jan 14, 2012

Also, I was now thinking - why do I need to back up the firmware if it's not stock anyways..
So I opened the KeyDB on the FirmwareTool 32 tab, clicked write and a window popped up saying "Drive returned Invalid Status!"
I also tried locking the drive since I'm stuck atm.. the lock failed too..

Log:

Code:

~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
JungleFlasher 0.1.91 Beta (300)
Session Started Sat Jan 14 14:14:53 2012

This is a 32 bit process running on 4 x 32 bit CPUs 
X360USB PRO detected, Version 0.18

Found 1 I/O Ports.
Found 1 Com Ports.
Found 7 windows drives A: C: D: E: F: G: H:
Found 3 CD/DVD drives E: F: H:

Sending Vendor Intro to port 0x0000
Status 0x90
Re-sending Vendor Intro: 
...............................................................................................
Serial flash found with Status 0x72

Sending Device ID request to port 0x0000
Spi Status: 0x8C
Manufacturer ID: 0xEF
Device ID: 0x11
Flash Name:  Winbond/NEX(W25P20/NX25P20)
Flash Size:  262144 bytes

Sending Spi UnLock request to Port 0x0000
...................................................................................................................................................................................................................................................................................................................................................................................
Spi Status: 0x00

Getting Status from port 0x0000
Invalid Status 0x0

Getting Status from port 0x0000
Invalid Status 0x0

Getting Status from port 0x0000
Loading firmware file D:\Xbox\JungleFlasher\Dummy.bin
MD5 hash:  7a2928a7f0861b7cc4d40028c5517040
Inquiry string found
Identify string found
Drive key @ 0xA030 078790003REMOVED3AB907E758333
Firmware Osig: [PLDS    DG-16D4S        0272]
Firmware is:  SlimKey Extract                 
Auto-Loading firmware file D:\Xbox\JungleFlasher\firmware\LTPlus-0272-v2.0.bin
MD5 hash:  e89c22ad8eecf634a3b27510901999c8
Genuine LT plus v2.0
Drive key @ n/a FFFFFFFFFFFFFFFFFFFFFFFFFFFFFFFF
Firmware Osig: [PLDS    DG-16D4S        0272]
Firmware is:  LT-Plus 2.0                     
Spoofing Target
DVD Key copied to target
Key Sector copied from Source to Target
Target is LT - ID strings not copied to Target


Getting Status from port 0x0000
Invalid Status 0x0

Getting Status from port 0x0000
Invalid Status 0x0

Sending Spi Lock request to Port 0x0000
Lock Failed !
Spi Status: 0x00

DUSTYB3N · Jan 14, 2012

What method did you use to unlock?

Search

Search

ANSWERED Slim-Un-Lock command returned an error

Deleted TX Member

peterrepek

Senior Member

doe1200

Deleted TX Member

doe1200

doe1200

Deleted TX Member

doe1200

Deleted TX Member

doe1200

Deleted TX Member

doe1200

jaycboy

Deleted TX Member

jaycboy

Deleted TX Member

peterrepek

Senior Member

Deleted TX Member

Deleted TX Member

DUSTYB3N