OK i installed the demon with no problems. i can read and write to both stock and demon. i have checked the ldv its 8. i have tryed all the dashboards (made sure dashboard are the same). it will glitch every time with in 2 cycles every time. but i try stock and i get the red dot. i have uninstalled and reinstalled and same thing. thanks for the help
slim will glitch but get red dot on stock
- Thread starter mmhone
- Start date
BL4K3Y
VIP Member
Does the console still boot fine regardless of the red dot?
If so, make sure that C15 is disabled.
If so, make sure that C15 is disabled.
no it just red dots on the stock after about 20-30 sec. i have also tryed ldv of 9 but still red dot.
BL4K3Y
VIP Member
Is this a Corona console by any chance?
If so, there are no EN timing files available yet (to my knowledge) so the CoolRunner isn't able to enable/disable itself when required.
If so, there are no EN timing files available yet (to my knowledge) so the CoolRunner isn't able to enable/disable itself when required.
BL4K3Y
VIP Member
Martin C
VIP Member
Why are you f**king about with your retail NAND?
Pardon my French but you shouldn't be manually writing ANYTHING to your 360 NAND. That's why you have a DemoN fitted.
Pardon my French but you shouldn't be manually writing ANYTHING to your 360 NAND. That's why you have a DemoN fitted.
Martin C
VIP Member
Martin C
VIP Member
Blakey, there are Corona DemoN Timing files available, just not public.
I will e-mail them to you if you need them, just shoot me an e-mail.
I will e-mail them to you if you need them, just shoot me an e-mail.
Yes I did. I read and wrote to the demon before install. I might be mistaken but the demon has a nand on it I am using for my glitch and you use the Xbox 360 nand for your second or stock nand
bernzburnz
BANNED
Me thinks you should of done a lot more reading and a lot less soldering. Xbox nand stays stock and DemoN nand get glitch image.
Martin C
VIP Member
so why are you messing with the 360 NAND at all?
There's no reason why it shouldn't boot still if you remove/disable the Coolrunner.
i have stock on the xbox 360( blue light off) and my glitch on demon(blue light on) i disabled my coolrunner by switching to prg and also removing the power wire. i have put the glitch nand on the xbox360 and it booted
---------- Post added at 10:51 ---------- Previous post was at 10:45 ----------
Initializing slim rgh#2 nand 2.bin..
Nand Initialization Finished
Load Files Initiliazation Finished
16202
Started Creation of the 16202 xebuild image
KV Info saved to file
---------------------------------------------------------------
xeBuild v1.06.555
---------------------------------------------------------------
building glitch image
---------------------------------------------------------------
C:\Users\kitchen\Desktop\try for stock\xxxxxxxxxxxx\new.bin image built, info:
---------------------------------------------------------------
Console : Trinity
NAND size : 16MiB
Build : Glitch
Xell : power on console with console eject button
Serial : xxxxxxxxxx
ConsoleId : xxxxxxxxxx
MoboSerial: xxxxxxxxxx
Mfg Date : 07/20/2010
CPU Key : xxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxx
1BL Key : xxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxx
DVD Key : xxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxx
CF LDV : 8
KV type : type2 (hashed)
---------------------------------------------------------------
xeBuild Finished. Have a nice day.
---------------------------------------------------------------
Saved to C:\Users\kitchen\Desktop\try for stock\
Image is Ready
XBOX360
Hardware : Demon Slim
Firmware : 1.0
Flash ID : 0x73AD Hynix (16MiB - Small block)
Flash Size : 0x400 blocks of 0x4200 bytes
Invalid Blocks : 0x27B
Writing Nand
Done!
in 0:32 min:sec
---------- Post added at 10:51 ---------- Previous post was at 10:45 ----------
Initializing slim rgh#2 nand 2.bin..
Nand Initialization Finished
Load Files Initiliazation Finished
16202
Started Creation of the 16202 xebuild image
KV Info saved to file
---------------------------------------------------------------
xeBuild v1.06.555
---------------------------------------------------------------
building glitch image
---------------------------------------------------------------
C:\Users\kitchen\Desktop\try for stock\xxxxxxxxxxxx\new.bin image built, info:
---------------------------------------------------------------
Console : Trinity
NAND size : 16MiB
Build : Glitch
Xell : power on console with console eject button
Serial : xxxxxxxxxx
ConsoleId : xxxxxxxxxx
MoboSerial: xxxxxxxxxx
Mfg Date : 07/20/2010
CPU Key : xxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxx
1BL Key : xxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxx
DVD Key : xxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxx
CF LDV : 8
KV type : type2 (hashed)
---------------------------------------------------------------
xeBuild Finished. Have a nice day.
---------------------------------------------------------------
Saved to C:\Users\kitchen\Desktop\try for stock\
Image is Ready
XBOX360
Hardware : Demon Slim
Firmware : 1.0
Flash ID : 0x73AD Hynix (16MiB - Small block)
Flash Size : 0x400 blocks of 0x4200 bytes
Invalid Blocks : 0x27B
Writing Nand
Done!
in 0:32 min:sec
The solder pad connection i have highlighted and the crushed wire both look suspect.
Don't like the look of that ground either, i would suggest using a fibreglass pen on the outer copper rim and soldering to that for a good ground.
i might be too pernickety but you can never be too careful.
Don't like the look of that ground either, i would suggest using a fibreglass pen on the outer copper rim and soldering to that for a good ground.
i might be too pernickety but you can never be too careful.
OK i fixed them. it still wont boot to a retail dashboard on either. it will glitch with both nands.( i unpluged the wire from the demon to make it glitch
Last edited:
U had any luck mate. Have u tried making a retail dash from your a working nand dump in jrunner. If that don't work try removing demon and flash the stock nand and see if it works.
Last edited: