LITEON 0225 SPUTNICK360 Unlock Tutorial for DG-16D4S MXIC memchips (soldering and trace cuts)

[TilVl]

Re: Russian 0225 Unlock Tutorial for MXIC memchips (soldering and trace cuts)

My drive is a MXIC.



Sending Device ID request to port 0x1190

Manufacturer ID: 0xC2

Device ID: 0x11

Flash Name: MXIC(MX25L2005)

Flash Size: 262144 bytes

 

[WalangAlam]

Re: Russian 0225 Unlock Tutorial for MXIC memchips (soldering and trace cuts)

lo, when you make the cut trace, is there suppose to be a resistant value in the line that you cut? or there should be no value in the multimeter since it was cut? I tested my cut using multimeter 20k and I got values. Does this means my cut was not totally cut?

 

[360backupman]

Re: Russian 0225 Unlock Tutorial for MXIC memchips (soldering and trace cuts)

Yea probably. THis should work on ALL versions of slim liteon. They're the SAME HW besides winbond and macronix.

 

[dLcrook]

Re: Russian 0225 Unlock Tutorial for MXIC memchips (soldering and trace cuts)

My drive is a MXIC.



Sending Device ID request to port 0x1190

Manufacturer ID: 0xC2

Device ID: 0x11

Flash Name: MXIC(MX25L2005)

Flash Size: 262144 bytes

I believe you should be able to go and try the unlock. I believe you should flash to stock fw for the old dash 13XXX, then update to 13599, then try the hack and update to LT+1.9 0272.

If your still not sure on everything, its ok to wait for what the team is working on and it will probably be released shortly (a week or less most likely)

 

[marcosgue]

Re: Russian 0225 Unlock Tutorial for MXIC memchips (soldering and trace cuts)

Hi! First sorry for my bad english


I think this is important. Has anyone managed to successfully activate the write protection again returning to the status 0x8E??

This way we could protect our devices against future updates.

 

[WalangAlam]

Re: Russian 0225 Unlock Tutorial for MXIC memchips (soldering and trace cuts)

Sending Device ID request to port 0x0000
Spi Status: 0x8C
Manufacturer ID: 0xEF
Device ID: 0x11
Flash Name: Winbond/NEX(W25P20/NX25P20)
Flash Size: 262144 bytes

Winbond Mediatek MT1335WE - 1025 - CMSL

will this work on Russian method?

 

[intensify]

Re: Russian 0225 Unlock Tutorial for MXIC memchips (soldering and trace cuts)

got it to work on the first shot with MXIC chip. gonna open up my other slims to see what they have

 

[WalangAlam]

Re: Russian 0225 Unlock Tutorial for MXIC memchips (soldering and trace cuts)

0x8C. damn

 

[conie]

Re: Russian 0225 Unlock Tutorial for MXIC memchips (soldering and trace cuts)

WalangAlam, yesterday I tried to unlock a Winbond over and over again but with no luck. I gave up...

 

[burnzy]

Re: Russian 0225 Unlock Tutorial for MXIC memchips (soldering and trace cuts)

winbond no luck, tried various resistors.

 

[Lizardpcs]

Re: Russian 0225 Unlock Tutorial for MXIC memchips (soldering and trace cuts)

A PMT probe just grounds mpx01 right? So why can't we just add a variable resistor to a PMT probe and use this to ground the point rather than soldering a resistor in etc?

Just an idea

 

[WalangAlam]

Re: Russian 0225 Unlock Tutorial for MXIC memchips (soldering and trace cuts)

WalangAlam, yesterday I tried to unlock a Winbond over and over again but with no luck. I gave up...

Tried 3.9ohms to 25ohms just for the sake experimenting but no luck either. Can't find the damn herring uber is right.

 

[goro.br]

Re: Russian 0225 Unlock Tutorial for MXIC memchips (soldering and trace cuts)

Tried 3.9ohms to 25ohms just for the sake experimenting but no luck either. Can't find the damn herring uber is right.

Yes, uber is right.
There is no solution for winbond at the moment. You can use TX-PCB solution or Pro kit for this.

 

[orgia71]

Re: Russian 0225 Unlock Tutorial for MXIC memchips (soldering and trace cuts)

the unlocking of non winbond 0225 is doable, you just do the procedures right, when you click unlock then be clicked even read status. I did not enter anything in his pocket saying stupidagini, in fact I only tarnish the reputation, I do have 15 years mod, I'm 38 years old and I'm not going to make fun of anyone. The method is fully functional, on the winbond datashets says he has worked with an absorbance of 2.7-3.6 volts 5mA, calculate the resistance, I can not test it because I do not have a PCB Winbond.

 

[WalangAlam]

Re: Russian 0225 Unlock Tutorial for MXIC memchips (soldering and trace cuts)

Some managed to unlock Winbond, using 3.5-5 ohms resistor. Attention! It's dangerous! The stabilizer can not stand and burn!

from 3 to 8 for Winbond (here must act carefully)

glad my pcb didn't burn

 

[<storm>]

Re: Russian 0225 Unlock Tutorial for MXIC memchips (soldering and trace cuts)

glad my pcb didn't burn

you have sucess on this??

 

[mgrover]

Re: Russian 0225 Unlock Tutorial for MXIC memchips (soldering and trace cuts)

well i got my sata card. the jmicron install was a breeze. so was intro. ive got winbond. ah f**k. at least i didnt buy a 40quid tool that I was going to use once...

 

[rk7987]

Re: Russian 0225 Unlock Tutorial for MXIC memchips (soldering and trace cuts)

Hey guys I hear that the X360Key is nice and easy process to play backups through USB is this correct, and it does not need any flashing or dumping ???

 

[guy_haron]

Re: Russian 0225 Unlock Tutorial for MXIC memchips (soldering and trace cuts)

Man are you on the wrong forum...
And it does require you dumping the key BTW.

 

[<storm>]

Re: Russian 0225 Unlock Tutorial for MXIC memchips (soldering and trace cuts)

anyone tried in Winbond Mediatek MT1335WE - 1005 - BLSL ????????????