Stage 1 Failed (via PMT probe v2)

V

Vickyvicksss

Noob Account
May 26, 2012
5
0
Canada
Hey guys, I apparently can't pass the first stage of extracting from my liteon 02510C

Tools I'm using and their settings:
CK3 Pro - Mode (blue light), switch to USB
Probe v2 (with an installed switch) - switch to probe, op switch is out, used the red MRA side to probe MPX01
Sata card
DVD drive tray half opened
Window Vista
JungleFlasher 0.1.96
Capture.JPG

1) CK3 Main power on. 3.3 volt switch on
2) Press phat key
3) Click yes
4) 3.3 volt switch off
5) connect probe to MPX01
6) 3.3 volt switch back
7) Wait until extract complete
8) Remove probe
9) Switch 3.3 volt off
10) Then click ok
-15 seconds later, I start getting the stage 1 failed messages.

On my third attempt (shown in my log), I tried waiting for 5 seconds and switching 3.3v on before I clicked ok, but it immediately gave me a "PhatKey failed" message.

Here's my log:
Code: 
~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
JungleFlasher 0.1.96 Beta (323)
Session Started Tue Apr 29 21:36:29 2014

This is a 32 bit process running on 2 x 32 bit CPUs 
portio32.sys Driver Installed 
portio32.sys Driver Started, thanks Schtrom ! 
Found 4 I/O Ports.
Found 1 Com Ports.
Found 7 windows drives C: D: E: G: H: I: J:
Found 1 CD/DVD drives E:


No Drive Detected! DVDkey files extraction aborted! 
 
Drive is Lite-On.. 
Sending Vendor Intro to port 0xEE00
Status 0x51
Re-sending Vendor Intro: 
..............
Serial flash found with Status 0x52

Stage 1 failed

Stage 1 failed

Extracted drive key failed Verification !


PhatKey extraction failed!

Drive is Lite-On.. 
Drive is Lite-On.. 
Drive is Lite-On.. 
Drive is Lite-On.. 
Sending Vendor Intro to port 0xEE00
Status 0x51
Re-sending Vendor Intro: 
.................
Serial flash found with Status 0x52

Stage 1 failed

Stage 1 failed

Extracted drive key failed Verification !


PhatKey extraction failed!


No Drive Detected! DVDkey files extraction aborted! 

Drive is Lite-On.. 
Sending Vendor Intro to port 0xEE00
Status 0x51
Re-sending Vendor Intro: 
..............
Serial flash found with Status 0x52

Stage 1 failed

Extracted drive key failed Verification !


PhatKey extraction failed!
Any help or suggestions will be much appreciated.
 
Last edited:
chase

chase

VIP Member
Apr 11, 2004
1,078
28
Toronto, Canada
Vickyvicksss said:
Hey guys, I apparently can't pass the first stage of extracting from my liteon 02510C

Tools I'm using and their settings:
CK3 Pro - Mode (blue light), switch to USB
Probe v2 (with an installed switch) - switch to probe, op switch is out, used the red MRA side to probe MPX01
Sata card
DVD drive tray half opened
Window Vista
JungleFlasher 0.1.96
View attachment 26518

1) CK3 Main power on. 3.3 volt switch on
2) Press phat key
3) Click yes
4) 3.3 volt switch off
5) connect probe to MPX01
6) 3.3 volt switch back
7) Wait until extract complete
8) Remove probe
9) Switch 3.3 volt off
10) Then click ok
-15 seconds later, I start getting the stage 1 failed messages.

On my third attempt (shown in my log), I tried waiting for 5 seconds and switching 3.3v on before I clicked ok, but it immediately gave me a "PhatKey failed" message.

Here's my log:
Code: 
~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
JungleFlasher 0.1.96 Beta (323)
Session Started Tue Apr 29 21:36:29 2014

This is a 32 bit process running on 2 x 32 bit CPUs 
portio32.sys Driver Installed 
portio32.sys Driver Started, thanks Schtrom ! 
Found 4 I/O Ports.
Found 1 Com Ports.
Found 7 windows drives C: D: E: G: H: I: J:
Found 1 CD/DVD drives E:


No Drive Detected! DVDkey files extraction aborted! 
 
Drive is Lite-On.. 
Sending Vendor Intro to port 0xEE00
Status 0x51
Re-sending Vendor Intro: 
..............
Serial flash found with Status 0x52

Stage 1 failed

Stage 1 failed

Extracted drive key failed Verification !


PhatKey extraction failed!

Drive is Lite-On.. 
Drive is Lite-On.. 
Drive is Lite-On.. 
Drive is Lite-On.. 
Sending Vendor Intro to port 0xEE00
Status 0x51
Re-sending Vendor Intro: 
.................
Serial flash found with Status 0x52

Stage 1 failed

Stage 1 failed

Extracted drive key failed Verification !


PhatKey extraction failed!


No Drive Detected! DVDkey files extraction aborted! 

Drive is Lite-On.. 
Sending Vendor Intro to port 0xEE00
Status 0x51
Re-sending Vendor Intro: 
..............
Serial flash found with Status 0x52

Stage 1 failed

Extracted drive key failed Verification !


PhatKey extraction failed!
Any help or suggestions will be much appreciated.
Click to expand...

you're suppose to remove the probe, power off, wait 5 seconds, power on then click ok
 
  • Like
Reactions: Vickyvicksss
V

Vickyvicksss

Noob Account
May 26, 2012
5
0
Canada
chase said:
you're suppose to remove the probe, power off, wait 5 seconds, power on then click ok
Click to expand...
I did that also. same results, but gave me the error immediately after I clicked ok. :/

EDIT:

Opps. Maybe I'm mistaken. Noobie question for you. When you and the jungleflasher prompt says "Power off", does that mean switch off the Ck3 pro?

EDIT 2:

On CK3 pro, switching it off and on didn't work.
 
Last edited:
Antalpromille

Antalpromille

VIP Member
Aug 4, 2011
3,158
0
Borås, sweden
Vickyvicksss said:
I did that also. same results, but gave me the error immediately after I clicked ok. :/

EDIT:

Opps. Maybe I'm mistaken. Noobie question for you. When you and the jungleflasher prompt says "Power off", does that mean switch off the Ck3 pro?

EDIT 2:

On CK3 pro, switching it off and on didn't work.
Click to expand...
When you are prompted to probe out should break the 3.3V line and ground mpx01 and then connect 3.3V again. Next prompt wants you to break 3.3V again and remove the probe and Waits 5 seconds to connect 3.3V again. Do this correct and it will work!
 
  • Like
Reactions: Vickyvicksss
V

Vickyvicksss

Noob Account
May 26, 2012
5
0
Canada
Antalpromille said:
When you are prompted to probe out should break the 3.3V line and ground mpx01 and then connect 3.3V again. Next prompt wants you to break 3.3V again and remove the probe and Waits 5 seconds to connect 3.3V again. Do this correct and it will work!
Click to expand...
Break 3.3V first, before removing the probe? I don't recall the prompt saying that, but okay, i'll try that. ;)

Update:

Nope. Same results. Stage 1 failed. Any other suggestions before I give up and move onto modding my ps3 instead?
 
Last edited:
Antalpromille

Antalpromille

VIP Member
Aug 4, 2011
3,158
0
Borås, sweden
Vickyvicksss said:
Break 3.3V first, before removing the probe? I don't recall the prompt saying that, but okay, i'll try that. ;)

Update:

Nope. Same results. Stage 1 failed. Any other suggestions before I give up and move onto modding my ps3 instead?
Click to expand...
And you are sure that the probe you are usling is directly connected to GND?
 
  • Like
Reactions: Vickyvicksss
meads1970

meads1970

BANNED
Jul 5, 2011
721
0
Lancashire
Practice makes perfect keep trying you will get it in the end
 
meads1970

meads1970

BANNED
Jul 5, 2011
721
0
Lancashire
silly question but it does happen the 3.3 volt switch is closest to the disc drive and not the CK3 Pro ? and the green light goes off on the probe when you press the 3.3 volt switch
 
  • Like
Reactions: Vickyvicksss
V

Vickyvicksss

Noob Account
May 26, 2012
5
0
Canada
Antalpromille said:
And you are sure that the probe you are usling is directly connected to GND?
Click to expand...
I think so. I'm using probe v2, and all I've done was adding a switch to the 3.3v line, which I believe is in slot 6


meads1970 said:
Practice makes perfect keep trying you will get it in the end
Click to expand...
But one also needs to learn how to quit and move on. :)

meads1970 said:
silly question but it does happen the 3.3 volt switch is closest to the disc drive and not the CK3 Pro ? and the green light goes off on the probe when you press the 3.3 volt switch
Click to expand...
Here are a couple of pictures.
SAM_0166.JPG
SAM_0167.JPG
The switch is in the middle of 3.3v line, and there is no green light on my probe. It flashes orange, which indicates "stand by" on it. Maybe that's the problem?
 
Last edited:
meads1970

meads1970

BANNED
Jul 5, 2011
721
0
Lancashire
This may or may not be the problem but ive only ever used the probe v3.using home made tools maybe wont get u support
 
meads1970

meads1970

BANNED
Jul 5, 2011
721
0
Lancashire
Or maybe just the wrong choice of nail varnish colour lol ;-) but im sure ur using the wrong tools
 
Last edited:
  • Like
Reactions: Vickyvicksss
V

Vickyvicksss

Noob Account
May 26, 2012
5
0
Canada
meads1970 said:
Or maybe just the wrong choice of nail varnish colour lol ;-) but im sure ur using the wrong tools
Click to expand...
Yeah I think it is my probe. Tried testing it with a different drive and same results. Time to return my $2 switch. Thanks a lot guys for helping and giving me suggestions. Much appreciated. :)
 
Antalpromille

Antalpromille

VIP Member
Aug 4, 2011
3,158
0
Borås, sweden
Before you give up, put the probe away and add an extra cable from GND and use that to probe instead. I never used the probe 2 but i think the closest you get to GND is 18 Ohm and that may be to far from GND for it to Works.
 
Last edited:
Antalpromille

Antalpromille

VIP Member
Aug 4, 2011
3,158
0
Borås, sweden
BL4K3Y said:
Have you checked that you get 3.3V from the switch when the drive is powered on?

Have you cleaned the MPX01 point?
Click to expand...
If he woulnt get 3.3V he wouldnt get any drive properties.
 
Last edited:
Antalpromille

Antalpromille

VIP Member
Aug 4, 2011
3,158
0
Borås, sweden
BL4K3Y said:
I want him to check to make sure his switch is working properly.
Click to expand...
But If the switch wasnt working the drive wouldnt get 3.3V, and If it doesnt jf wouldnt give any drive properties. From the picture OP posted i can tell that he gets drive properties so i would såg it at least closes correctly. Thats what i meant :)
 
You must log in or register to reply here.