LITEON DG-16D4S - SLIM Status Code error

[demon2011]

I've just fitted a tx pcb into my brothers 9504 slim and everything seemed fine but when i updated to the latest dash by usb i got this error below and can't get past it. I did the same to mine and never got this, please help.

Status Code

3151-351f-b600-0401-c000-0022

 

[diaboliq20]

what dash were u updating from?

 

[demon2011]

Can't remember but it was pre drive lock.

 

[Travo112]

...I would swap back to the original drive during updates to be safe IMO

 

[demon2011]

Well i did'nt want to lock the orig board, so what are my options now.

 

[frazzeld]

Original PCB...revert to stock firmware, USB update (drive has to lock) your trying to update with an unlocked TX board...."It can't lock the drive"

 

[demon2011]

I updated my 0225 drive and didnot run into this error but am I supposed to set the tx pcb to unlock as I kept the switch to lock. Can't remember if I did when I updated my slim. Just did not fancy soldering the orig pcb back in to update but if that is the only way then i'll have to.

 

[diaboliq20]

the update is tryig to change the SPI status on that PCB....it didn't happen on yours because yours was locked from factory so the update didn't need to change the SPI status

 

[demon2011]

Ya but I updated to the latest dash after I had the tx pcb installed on my 0225.

 

[diaboliq20]

yes - but the update sees the fact that your drive is an 0225......because of this it doesn't attempt to lock the SPI as m$ assume it as already locked......
with the 9504 (now 0272) it tries to lock the SPI on the 13599 update and fails on the TX PCB as this cannot be softlocked......it's looking to lock the SPI this time on your friends PCB

 

[FlashDrive360]

0225 is factory lock so you wouldnt get and error, 9504(0272) not factory locked microsoft need to lock the drive for the update to work properly then you can use TX board so you will need to put stock board in the console

 

[nosherfj]

i sold my 9504 slim for this reason and bought a 0225 slim with tx board.didn't fancy all this pcb hot swapping.

 

[diaboliq20]

thing is - u only need to do it once.......after m$ lock the SPI on the original PCB....they wont attempt to do it again

 

[demon2011]

Ya sorry matey i get what your on about now, i went in thicko mode. I'll solder the orig pcb back update and replace with tx after.

 

[nosherfj]

thing is - u only need to do it once.......after m$ lock the SPI on the original PCB....they wont attempt to do it again

what a pain. glad i got a 0225 no hot swapping every system update

 

[diaboliq20]

what a pain. glad i got a 0225 no hot swapping every system update

you don't need to hot swap after this....unlock TX PCB....flash stock fw......lock PCB.....update dash......unlock PCB....flash CFW......lock PCB

remember - m$ wont change the SPI again....only check it

 

[frazzeld]

Ya sorry matey i get what your on about now, i went in thicko mode. I'll solder the orig pcb back update and replace with tx after.

is the original board a Winbond or MXIC

Dont forget to revert to stock before you update

 

[demon2011]

Right i've put the orig pcb back and it resumed the update and now goes into the dash. Am i going to have to reflash the tx pcb or will it be fine the way it is.

 

[diaboliq20]

what fw is flashed to the TX PCB?

 

[demon2011]

Lt+ 1.92