temps

[nospmohtkcin]

has anyone noticed that using evox dash the cpu and m/b will not change temps and stays at 64.0C and 64.3C

 

[freakzilla3333]

In xbox media center, mine is usually about 50 degrees c.

 

[NeOnRaBbIt]

it changes but it takes about 1 or 2 minutes fr the temp to update..

 

[PhatheadWRX]

has anyone noticed that using evox dash the cpu and m/b will not change temps and stays at 64.0C and 64.3C

Temps are not correct with v1.6

Don't trust what it says. If you run 50-60% fan speed you should never have an overheat problem

 

[nospmohtkcin]

has anyone noticed that using evox dash the cpu and m/b will not change temps and stays at 64.0C and 64.3C

Temps are not correct with v1.6

Don't trust what it says. If you run 50-60% fan speed you should never have an overheat problem

figured that. I've been running my fan at 55% anyways and will probably put in a 80mm fan and 12v it next week just to be on the safe side

 

[MACK45]

Benq flashing help

hello can anyone help me plz i did the benq unlock bit and it worked but when i do the device bit it comes up with a box saying MTK vendor intro failed If you wish to resend the command click yes power of the drive then back on (within the 1 second) then i click yes but still says failed

 

[ReMix]

Re: Benq flashing help

that's because benq unlock already sends the device intro

just hit read after benq unlock

 

[MACK45]

Re: Benq flashing help

what's the best version of jungleflasher i im trying to uuse 0.1.73 but it crashers

 

[GodZilla]

Re: Benq flashing help

1.73 IS the best version

When is it crashing?

 

[MACK45]

Re: Benq flashing help

when i do the read

 

[GodZilla]

Re: Benq flashing help

What SATA chipset you using?

 

[MACK45]

Re: Benq flashing help

dont know its not crashing now but it will not read now

 

[GodZilla]

Re: Benq flashing help

are you plugging the SATA cable into a port on your mobo or a VIA card?

 

[MACK45]

Re: Benq flashing help

my mother board i get the info when i unlock and i got the read to work with JungleFlasher v0.1.64 Beta but the write will not work

 

[MACK45]

Re: Benq flashing help

right i open jungleflasher 1.73 then go to benq unlock then is says Sending Magic Keys to Drive on port 0xF000
..........................................
Done!
Sending Vendor Intro
Requesting Device ID
Manufacturer ID: 0xC2
Device ID: 0x11
Flash Name: MXIC(MX25L2005)
Flash Size: 262144 bytes

then i go to read and it says
reading bank 0 .... then crashers

 

[GodZilla]

Re: Benq flashing help

sounds like SATA problems mate! try using the primary port on your mobo!
(you'll probably have to move the HD cable to another one first!)

 

[MACK45]

Re: Benq flashing help

i tryed it in the outher port but same prob i have the files of the dvd drive

 

[MACK45]

Re: Benq flashing help

i have a outher console that is flashed is there any way to swop the drives over so it works

 

[ReMix]

Re: Benq flashing help

sorry man, no way to do that
only way to get that box to play backups is to flash that drive

you need the keys off it

 

[MACK45]

Re: Benq flashing help

i have the key of the benq drive but not tryed to get the on off my light on yet