Trinity CR4 won't glitch

[aden34]

i have everything installed but when I try and boot into xell to get my cpu key, it won't boot. Red light stays solid and I just get a black screen. I have messed with the switches and pins but the best I could get was a solid green (debug) light. Didn't blink or anything

I tried creating a .ecc with my nand, then downloaded a .ecc as well from the cr4 Magic smc thread or whatever, and still nothing

The ground wire has been changed in this picture to the AV

 

[john mathews]

look like solder

 

[15432]

1. you don't need postfix for Trinity
2. why your switch is in Phat position?
3. how did you set DIPs?

 

[john mathews]

1. you don't need postfix for Trinity
2. why your switch is in Phat position?
3. how did you set DIPs?

looks like he lifted post out pad

 

[aden34]

Had to post fix trinity because the wire got ripped from the solder point taking out all the solder so now i can't add solder to it

These were taken yesterday before j tried this. Already switched it to slim and still the same issue

Dips are set to 3/4 also tried 2/6 and 3/8

 

[john mathews]

we need to see some logs that u created and wrote the ecc to xbox

 

[aden34]

just checked, that wasn't solder by cpu_rst

here's the log for the nand dumps

J-Runner v0.3 Beta (7) Started






Checking Files
Finished Checking Files
Version: 10
Flash Config: 0x00023010
00023010
Trinity, Jasper 16MB
CB Version: 9231
Trinity
Reading Nand to C:\Users\Aden\Desktop\J-Runner v3 (5) Core Pack\output\nanddump1.bin
Reading Nand
Done!
in 3:25 min:sec


Reading Nand to C:\Users\Aden\Desktop\J-Runner v3 (5) Core Pack\output\nanddump2.bin
Initializing nanddump1.bin..
Trinity
Glitch2 Selected
Nand Initialization Finished
Reading Nand
Done!
in 3:24 min:sec


Reading Nand to C:\Users\Aden\Desktop\J-Runner v3 (5) Core Pack\output\nanddump3.bin
Comparing...
Nands are the same
Reading Nand
Done!
in 3:24 min:sec


Reading Nand to C:\Users\Aden\Desktop\J-Runner v3 (5) Core Pack\output\nanddump4.bin
Comparing...
Nands are the same
Reading Nand
Done!
in 3:24 min:sec


here's the log for the first .ecc write

Checking Console..
Version: 10
Flash Config: 0x00023010
00023010
Trinity, Jasper 16MB
CB Version: 9231
Trinity
Initializing nanddump1.bin..
Trinity
Glitch2 Selected
Nand Initialization Finished
ECC created
CR4 Selected
ECC created
Version: 10
Flash Config: 0x00023010
Writing Nand
image_00000000.ecc
Done!
in 0:18 min:sec

this is the log for when i tried using the ecc from the magic smc thread

Checking Console..
Version: 10
Flash Config: 0x00023010
00023010
Trinity, Jasper 16MB
CB Version: 9188
Trinity
Trinity Manually Selected
Version: 10
Flash Config: 0x00023010
Writing Nand
TRINITY.ecc
Done!
in 0:19 min:sec

 

[john mathews]

u haven't created ecc or written it to nand don't see it

 

[aden34]

in the first one, i created a ecc, then realised it cr4 wasnt selected, selected it, then recreated the ecc and wrote

 

[ablegepu]

I can't see it perfectly on my phone but looks almost like c5r11 cpu-rst is ripped did you just solder the wire you the trace? or am I wrong and the pad is there

 

[aden34]

I can't see it perfectly on my phone but looks almost like c5r11 cpu-rst is ripped did you just solder the wire you the trace? or am I wrong and the pad is there

no it's still connected. i tinned the point as well as the wire, then soldered it on. just the way the solder looks i guess

 

[L2000]

Touch up C5r11 and your GRND wire make sure its properly soldered to chip and AV.

 

[ablegepu]

Well I'm with john though next to c5r11 it looks like a big splash of solder flooding the capacitor c5r14 and the resistor right beside it.

 

[aden34]

Well I'm with john though next to c5r11 it looks like a big splash of solder flooding the capacitor c5r14 and the resistor right beside it.

that was flux i belive. went through and checked and saw nothing. wiped away whatever was there and still have the issue. just touched up that spot so now ill see how it works

okay, so now it is trying to glitch and the green light is blinking. but then it just stops, and i have no signal to my monitor

 

[L2000]

have you also retouched up the GRND wire to chip and AV port yet?

 

[john mathews]

u have hdmi or cables plugged in/ sounds like it glitched

 

[aden34]

have you also retouched up the GRND wire to chip and AV port yet?

yes i did

u have hdmi or cables plugged in/ sounds like it glitched

i do. i try to switch input then it brings my right back to my computer input, meaning that it didn't find a signal

 

[john mathews]

u have hdmi plugged into tv - to xbox/ n on the right channel/ u can also do a ip scan for xell

 

[aden34]

u have hdmi plugged into tv - to xbox/ n on the right channel/ u can also do a ip scan for xell

Well before I was using the standard av to vga cable, but now I'm using HDMI and the green light blinks about once or twice then the green light will stay solid with no picture

 

[ablegepu]

do you know what the optical audio port is. on trinity you can see a slit in the back side of the optical audio port and when you see the red light come on through that slit it means the console has booted. or you can stick something in where the optical port flap is and see the light.