TRINITY DEMON WONT BOOT RETAIL

[stucknvegas]

TRINITY 16 MB.
Dash 16547
Proto V-2 & Demon
Console was working before
The console boots the RGH Image with the demon selected.I shut the console down. Toggle the Demon controller switch
The blue light is off no picture for the retail dash with original Nand I did use the Demon selection toggle Function in JRunner
to write back the original and the the RGH Image. This is my First Demon Install !! What am I overlooking Thanks









View attachment 25723View attachment 25722View attachment 25725View attachment 25726View attachment 25724View attachment 25727View attachment 25728View attachment LOGS.txt

 

[BL4K3Y]

Is that log correct?

It looks like it is from a different session because there is nothing there that tells me you even attempted to read the XBOX 360 NAND using the DemoN.

Did you write anything to the XBOX 360 NAND?

 

[stucknvegas]

Sorry I was not clear about that I did the proto 2 Install 2 weeks ago with out demon installed ..Never read original nands with Demon
I am inserting original logs now Also This console Started off with REV-C Installed Then Proto 2 Both worked Well

 

[BL4K3Y]

Version: 03
Flash Config: 0x00023010
Writing Nand
updflash.bin
Done!
in 2:06 min:sec

It looks like updflash.bin (glitch image) is written to the console's NAND.

You should read that back a couple of times (just in case) and then write nanddump1.bin to the XBOX 360 NAND.

 

[stucknvegas]

Ok Will Try Again oops!!! I am sure making My first Demon Look harder than it Should Be
Thanks for the Quick Help BL4K3Y

 

[BL4K3Y]

Ok Will Try Again oops!!! I am sure making My first Demon Look harder than it Should Be

If what I said is correct, you just forgot to write the stock NAND image back to the console's NAND.

Once you have written it back, your console should boot from both NANDs without any trouble at all.

 

[stucknvegas]

I wrote the stock image back to the Consoles Nand and it shows it is successful
Like this> Load original dump in buffer 1 Select retail >Toggle Xbox in JRunner Demon function
Select Write> Warning you are writing to Xboxs nand Done.. Still the Same no retail
Also when I attempt to read the Consoles Nand on the second read JRunner Freezing The not Responding windows Error
and also you are about to overwrite your nand dumps message sometimes
I have the original Nand dumps in off line location.. I got something wrong still I attached another log thanks

 

[gavin_darkglide]

if u write the retail nand to the demon and disconnect the 5v from proto, does it boot? then see if it boots from xbox.

 

[stucknvegas]

Ok will do Thanks Gavin

 

[stucknvegas]

Yes retail from demon nothing from OG nand

 

[gavin_darkglide]

Well, if it booted stock from stock nand with the stock image written to demon, I would tell you to check the SBR wire. Try writing back stock image to stock nand using the demon remap option under advanced menu.

 

[stucknvegas]

I checked the SBR wire with a meter tested OK Installed a new wire anyway .Wrote the Xboxs original Dump to the Xbox nand
using Advanced Demon remap option and still the same..The machine wont boot from its own nand

 

[Martin C]

Define 'won't boot' - it must be doing something?

 

[stucknvegas]

Hi Martin It will start the glitched or Retail retail Image from Demon only On the the consoles nand just center green light from ROL Does not start

 

[keil423]

Test the Stby_CLK or it think its the R3B15 resistor next to the hana chip. Consoles with demons tend to act a little different and I have had several that wouldn't boot retail but would boot the demon with no trouble. Most of the time I found that resistor to be blown or the trace to be damaged.

 

[stucknvegas]

Thanks Keil I did have a piece of Kynar soldered there. with the coolrunner installed But it looks and Tests good I have done trace repairs
of standby trace a couple of times I tested from the resistor to point by the south bridge were it changes to underside of motherboard
It is clean This console worked fine with Proto installed before i installed the Demon

 

[gavin_darkglide]

If the console is turning on at all it is not the stby_clk point. 1 of the points around it may be messed up though.

 

[Martin C]

Hi Martin It will start the glitched or Retail retail Image from Demon only On the the consoles nand just center green light from ROL Does not start

In which case the NAND isn't initialising properly. It could be a bridge or trace somewhere. I'd check all I/O points and resistors tied to them.

If possible, post clearer images of the soldered areas around the DemoN and the topside NAND (just in case). If it's out of focus, simply move away until it's focussed. Don't waste people's time by posting blurred images.

 

[stucknvegas]

 

[stucknvegas]

Sorry for the Blurry pictures in the original post I touched up the Small solder points under the Nand
Now Will test all resistors I/O of Nand area Thanks to all that have Helped me out so far