Trinity problem

[criscus2004]

Hello guys it's my first Trinity and i'm stuck. First i read my nand like 10 times and every time i had a bad block but i understand that's ok (j-runner said that the nands are the same). After that i wrote the DGX.ecc and try to get my Cpu key without succes (tried also some wire lenghts that i read in previous threads).
After that i wanted to get back to stock and J-runner said "Flash Config: 0x00000000 Can not Continue".
I remade and cleaned my soldering 5 times because i read that in most cases this is the problem. Also uploaded some pics to show you if my soldering is good.

This is the log in j-runner when it is comparing the nands:
"Comparing...
Bad Block ID @ 0x02D7 [Offset: 0xBB6E00]
Bad Block ID 02D7 Found @ 0x03FF [Offset: 0x107BE00]
Block ID 03FF [Offset: 0x107BE00] remapped to Block ID 02D7 [Offset: 0xBB6E00]
Bad Blocks Remapped
Initializing nanddump1.bin..
Nand Initialization Finished
Comparing...
Bad Block ID @ 0x02D7 [Offset: 0xBB6E00]
Bad Block ID 02D7 Found @ 0x03FF [Offset: 0x107BE00]
Block ID 03FF [Offset: 0x107BE00] remapped to Block ID 02D7 [Offset: 0xBB6E00]
Bad Blocks Remapped
Bad Block ID @ 0x02D7 [Offset: 0xBB6E00]
Bad Block ID 02D7 Found @ 0x03FF [Offset: 0x107BE00]
Block ID 03FF [Offset: 0x107BE00] remapped to Block ID 02D7 [Offset: 0xBB6E00]
Bad Blocks Remapped
Nands are the same"
Why can i do to fix it?

 

[Joo C]

Is your power plugged in when trying to write the nand? if so, have you tried hitting the reset button on your nandx or restarted your pc?

 

[criscus2004]

Yes the device is plugged in, also tried the reset button on my jr-programmer, reinstall driver, restarted pc and i have the same error.

 

[Joo C]

Let's for the moment assume that there is a problem with your nandx...(if you powered on the console with it attached it may very well be the case)

You've already written the DGX ecc. so I would suggest you boot Xell and use Xell to write back the new nand via usb flash drive

---------- Post added at 15:11 ---------- Previous post was at 15:09 ----------

Just read your post again - do you have the power cable attached and on standby when trying to flash the image??

 

[criscus2004]

The power cable was attached and on standby when i wrote the DGX.ecc but it didn't boot Xell. When i power up the console it starts but it doesn't do anything.
All i have for the moment is my stock nand.

 

[Krafter]

Do you have the rest of your log? I don't see where you wrote the DGX ecc to the NAND.


Sent from my iPhone using Tapatalk

 

[criscus2004]

I wrote the Dgx.ecc with succes but i did not save the log

 

[Martin C]

Does the console power on ok?

 

[criscus2004]

When i turn the console on it starts, after that i get the red dot and after that nothing is happenig.

 

[Martin C]

how long until a red dot?

What values are you getting from the NAND points (use my NAND-x troubleshooting thread for help)?

Is this with a NAND-x or J-R Programmer?

 

[criscus2004]

I have the jr-programmer

 

[Joo C]

Martin asked how long until u get the red dot for a reason-u may have successfully written the DGX ecc and that implies u can continue extracting the keys

 

[Martin C]

What values are you getting from the NAND points (use my NAND-x troubleshooting thread for help)?

Help us to help you.

 

[criscus2004]

It takes about 27 seconds till i get he red dot. Later i will try to find the values of my nands points because i dont have a multimetter.

 

[Martin C]

It takes about 27 seconds till i get he red dot. Later i will try to find the values of my nands points because i dont have a multimetter.

Then you shouldn't be soldering without one.

27 secs sounds like LDV.

 

[criscus2004]

Those are my values from nand points:
1 - 1v
2 - 3.3v
3 - 1v
4 - 0v(42 Ohms)
5 - 3.1 v
6 - 0v(5.7 Kohms)

And i posted a picture with my LDV.

 

[Martin C]

What you circled is NOT your flashconfig.


So what's the problem here? You can obviously read/write to the console ok?

 

[criscus2004]

I cant read/write the console, when i power the console i get the red dot and when i try to read or write i get this error in J-runner " Version: 01 Flash Config: 0x00000000 Can not Continue".I checked the soldering with the multimeter and it looks ok.
I dont know what to do anymore......

 

[Martin C]

Check continuity from each soldered point back to the J-Runner programmer.

Reboot the PC.

Try again.

 

[criscus2004]

I checked each soldered point back to j-runner programmer and continuity looks ok. Restart the pc and..... same error.