Trinity problem

H

Heronimoh

Full Member
Feb 6, 2011
39
0
SPAIN
criscus2004 said:
I cant read/write the console, when i power the console i get the red dot and when i try to read or write i get this error in J-runner " Version: 01 Flash Config: 0x00000000 Can not Continue".I checked the soldering with the multimeter and it looks ok.
I dont know what to do anymore......:(
Click to expand...
Do you read flash with the power on?
You only have to connect the power and NOT power on the console. The read/write is with console power OFF.
 
D

downdog2519

Noob Account
Jan 5, 2013
5
0
when you plug in the power cable is the console just going striaght to red light even before touching the power button etc?
 
yoohoomat

yoohoomat

BANNED
Dec 21, 2012
56
0
Murfreesboro, TN
criscus2004 said:
I cant read/write the console, when i power the console i get the red dot and when i try to read or write i get this error in J-runner " Version: 01 Flash Config: 0x00000000 Can not Continue".I checked the soldering with the multimeter and it looks ok.
I dont know what to do anymore......:(
Click to expand...
I am going to throw this out there but your nand x seems to be on version 1 you need to update it to version 3 should solve your issue on the write stuff.
 
yoohoomat

yoohoomat

BANNED
Dec 21, 2012
56
0
Murfreesboro, TN
BL4K3Y said:
J-Runner supports any NAND-X ARM firmware (I think).

The V3 ARM firmware is only required for CPLD programming.
Click to expand...
It may but I had problems with one of my nand x on a older version trying to read and write I updated it and it worked fine but like I said it was just a thought but even if he did take the time to update would not hurt.
 
C

criscus2004

Junior Member
Aug 24, 2010
17
0
Heronimoh said:
Do you read flash with the power on?
You only have to connect the power and NOT power on the console. The read/write is with console power OFF.
Click to expand...
Yes i connect the power but not powered on the console.

---------- Post added at 09:12 ---------- Previous post was at 09:11 ----------

I will post later a picture of my soldering connected to J-Runner programmer because i'm not home for the moment.

---------- Post added at 09:15 ---------- Previous post was at 09:12 ----------
downdog2519 said:
when you plug in the power cable is the console just going striaght to red light even before touching the power button etc?
Click to expand...
No first green light and after 27 seconds red light.
 
Last edited:
Martin C

Martin C

VIP Member
Jan 10, 2004
35,981
0
Scotland, UK
www.team-xecuter.com
yoohoomat said:
I am going to throw this out there but your nand x seems to be on version 1 you need to update it to version 3 should solve your issue on the write stuff.
Click to expand...
He said he has a J-R Programmer.
 
C

criscus2004

Junior Member
Aug 24, 2010
17
0
Yes the console was plugged in. I dont have another console but i will try tomorrow with t another Nand-x (borrowed from a friend) and see what happens.
 
C

criscus2004

Junior Member
Aug 24, 2010
17
0
I have measured my nand points again :
1 - 0.1v
2 - 3.3v
3 - 0.1v
4 - 0v(42 Ohms)
5 - 3.1 v
6 - 0v(5.7 Kohms)
I think no.1 and no.3 not have the right values.
 
C

criscus2004

Junior Member
Aug 24, 2010
17
0
I solved the problem at last :). I ordered another jr-programmer and it worked like a charm.
Wrote the dgx.ecc file and then Xell booted in less than a minute( I used 11 cm wire for cpu-rst on point FT4R2 and 120 cm for post_out) and got my cpu key finnaly!
Thanks for suppport guys especially Martin C :)!!!
 
hotbird_05

hotbird_05

BANNED
Jun 25, 2012
211
18
criscus2004 said:
I solved the problem at last :). I ordered another jr-programmer and it worked like a charm.
Wrote the dgx.ecc file and then Xell booted in less than a minute( I used 11 cm wire for cpu-rst on point FT4R2 and 120 cm for post_out) and got my cpu key finnaly!
Thanks for suppport guys especially Martin C :)!!!
Click to expand...

Really good news

Well done
 
Last edited:
You must log in or register to reply here.