RGH Trinity rgh slim help needed

[rolacoasta]

TX Product(s) used: Coolrunner rev c, Jr programmer v2
Console Type: trinity
NAND size: IDK. Cant boot into xell.
Dashboard version: 16756
CB version: IDK
Screenshot of NAND details from J-Runner:

Description of problem: Ok, so now i try to boot into xell and my xbox flashes green lights for like 10 seconds and then it just goes red and stays solid. The same happens if i just try to boot into a stock nand. I need expert help! Im lost at this point. I re wrote my stock nand to my xbox and it wont turn on. At first i read my nand 2wice and they matched. Like an idiot i then updated my console to the latest dash not knowing what would happen. Then i flashed my coolrunner with the nand files from before i updated. I know have no clue where to start now. I cant boot into xell or power the console on through the power button to boot to the regular dash. At first it was just a flashing green light but when i re wrote my nand it flashes green and goes red. Please help. If there is anything im missing just let me know. I filled out the template as best i could.

Was the console working before you started: Yes

Do you get a green debug light appear on the RGH chip every 4-5 seconds: No

 

[chase]

add pictures of your soldering and your TX products

also, post your j-runner log

 

[rolacoasta]

 

[rolacoasta]

How do i add my jrunner log? i just deleted it and re downloaded it so i dont think there is any logs left.

 

[Joo C]

Your E wire is in the wrong place

 

[rolacoasta]

Ok thanks

 

[Joo C]

The green wire is soldered to ground, it should be opposite the brown wire

 

[jligg]

Your stock nand isnt working because after you read it ypu updated your console, so now the ldv is incorrect

 

[rolacoasta]

Ok. so now i have re soldered it to the correct point. the xbox still wont boot into xell and it just flashes green but doesnt turn red anymore. What now?

 

[15432]

Now you should do some magic with wiring (alter len of rst cable, place it in another place, try to alter switches, another timing, etc...) and run XeLL. You need cpu key even to restore stock

 

[rolacoasta]

Ok. so now i have re soldered it to the correct point. the xbox still wont boot into xell and it just flashes green and then turns red. What now?

 

[Joo C]

What do u mean when u say 'I flashed my coolrunner with the nand files from before i updated'?

 

[jligg]

Thats why we need the jrunner log..did you even write xell to the nand? In your op you never said ya did

 

[rolacoasta]

i mean i created the ecc file and wrote it to my coolrunner. this ecc file was created from the nand files from before i updated. i read my nand. updated my console. then created an ecc. then wrote it to my coolrunner.

 

[jligg]

The ecc gets wrote to the consoles nand

1. Load your nand that you read in the source box
2. Select the rgh2 radio button.
3. Select dash 16747
4. Hit create ecc button
5. hit write ecc button

make sure your jr programmer is hooked up with power supply plugged in

 

[rolacoasta]

my bad. I read my nand then updated my console then created an ecc then wrote it to my nand. I resoldered the pointon my xbox but it still wont ddo anything. shoul i try to re write the ecc? or what? i try to boot it up with the power button also and i get the same result. What do i do?!

 

[jligg]

did you program your rev c with the rgh2 trinity file?

 

[jekdyell]

Your Cpu Rst Wire Is Solder To The Wrong Point It Should Be On FT4R2 & Not FT4R5.:wink:

 

[rolacoasta]

at this point i dont even know which file i used for the trinity. Im going to re solder the cpu rst wire and see if that does anything. Thanks for all the amazing help. you guys are real pros!

 

[gavin_darkglide]

Dont worry about glitch timing yet. Just write ecc, wire up coolrunner, program coolrunner with trinity xsvf. then turn on the console and wait. sooner or later it will boot xell. after you get the cpu_key, you can adjust wiring for better boot times. also look at this,http://team-xecuter.com/forums/showthread.php?t=86641 as there are jumpers on the coolrunner which can be changed, and may give better boot times. Either way it is good information.