RGH Trying to flash back glitched NAND

[arcadekidflo]

TX Product(s) used: e.g J-R Programmer, CR3 Lite

JR Programmer v1 , Coolrunner rev C ( genuine )

Console Type: (Xenon/Zephyr/Falcon/Opus/Jasper/Trinity/Corona etc).

Trinity

NAND size: 16/256/512/4GB

16

Dashboard version: e.g 2.0.14699

2.0.16767.0

CB version: e.g 5771

??

Screenshot of NAND details from J-Runner:
(attach an image to your post)

J-Runner log:
updflash.bin log (if applicable):

attached

Image of Coolrunner:
Images of close-up soldering to motherboard:
(attach images to your post)

Soldering is ok ( not done by me ! )

Description of problem:

Console was RGH in summer 2012 when the dashboard was 14719 . I used it for a while then flashed the retail dash again . Now i want to flash glitched NAND again , i have the nanddump.bin , the cpukey etc.. i tried to make a 16203 image but when flashing i was getting error writing at every block . I have a QSB installed , connection should be solid . Check the log to see what happened

Was the console working before you started: Y/N

Yes

Do you get a green debug light appear on the RGH chip every 4-5 seconds: Y/N

No

How long is the light on for each time:

Constant red light

 

[Taijigamer2]

Please re-check Nand X soldering, and provide pics of install.

 

[arcadekidflo]

I'll be able to do that only tomorrow . The soldering i think is ok because a while ago i flashed the retail dash and it worked . The writing error is on absolutely every single block , which i think means simething else , not bad soldering

 

[Taijigamer2]

Can still be a sign of bad soldering. Check out this thread for more info

http://team-xecuter.com/forums/showthread.php/77908-Troubleshooting-NAND-x-connection-problems

good luck.

 

[arcadekidflo]

Here's a pic of the QSB soldered

 

[Taijigamer2]

I would add flux and reflow those NAND qsb points, they look dull, did u use tin solder? Did u check the voltages with a multimeter as per the guide?

 

[arcadekidflo]

Soldering is good , tried to read the NAND again and i get an error Flash Config: 0x00000000 Can not Continue
I'm attaching the JRunner log with what i was trying to do last year, i think i wanted to flash a glitched nand but also update it .
Please help , the console is dead , did i flash something wrong ? Log attached

 

[ChoCho346]

Soldering isn't good which is why you receive that error. Just looking at that qsb its noticeable it needs to have flux added and retouched.

 

[sebastian79hl]

I agree to ChoCho...

Everything needs to be soldered OUT, CLEANED, and that properly soldered in angain with the need of FLUX!

Looks awful dude...

 

[arcadekidflo]

QSB was taken down , area cleaned with alcohol , then the soldering was done again with no QSB , by a professional modder . Unfortunately , the same error occurs , it is like the NAND is not getting any power

 

[ChoCho346]

You do have the power supply connected correct? Depending on how your points are as well you should try the bottom side of the board.

 

[ablegepu]

You need to post clear pictures of the whole cool runner and all points on the motherboard that have been soldered to as well as straight clear overhead pictures of the qsb. If you do all of that we can probably help you better, but if you can't do that then we really can only help you half-assed.