Hi guys im trying to get cpu key i have soldered and successfully obtained 2 successful nand dumps then i updated jrunner and now when i try to read nands so i can try and flash coolrunner i keep getting the above error i have tried to resolder points again with no success is my soldering craps coz it worked the first time or is there a problem with the nand x or have i stuffed the motherboard up please help i unable to go any further thanks. Btw im using nand x v3, j runner and trinity motherboard with orginial dash of 12149.
trying to re read nand but keep getting Flash Config: 0x00000000 Can not Continue
- Thread starter championbowler
- Start date
BL4K3Y
VIP Member
It's hard to tell what your soldering is like with those images.
I suggest you take some more with Macro mode enabled on your camera so you can get good, clear shots.
I suggest you take some more with Macro mode enabled on your camera so you can get good, clear shots.
i thought that might be the case alright im onto it thanks for respondinga.
here are the best i can get
here are the best i can get
Last edited:
sorry not sure what u mean im a noob if you mean connect the power to the motherboard i have and its fine
BL4K3Y
VIP Member
Your soldering looks to be fine, but again, I can't tell.
Clean up that flux and post some decent images.
Without images, we can not possibly help you.
Clean up that flux and post some decent images.
Without images, we can not possibly help you.
crashxtrme
Full Member
alexander_1333
VIP Member
Your soldering looks good to me.Try to download J-Runner again.Read from the new one.It could be the update is going wrong.
Once i updated J-Runner and when i ty to read nand i only got this error:
J-Runner Has Encountered an Error and Needs to Close......
Once i updated J-Runner and when i ty to read nand i only got this error:
J-Runner Has Encountered an Error and Needs to Close......
ok i just re downloaded j runner and tried to nand dump however still getting the same error
---------- Post added at 18:46 ---------- Previous post was at 18:43 ----------
sorry not sure what u mean by is the xbox powering on? There is power coming from the ac supply i know this coz the red light comes on the coolrunner. Is that what u mean?
---------- Post added at 18:46 ---------- Previous post was at 18:43 ----------
sorry not sure what u mean by is the xbox powering on? There is power coming from the ac supply i know this coz the red light comes on the coolrunner. Is that what u mean?
Antalpromille
VIP Member
Since the coolrunner cables are installed, please take a picture in the hana-area. If stby_clk resistor/trace are damaged, it could give the same problem.
alexander_1333
VIP Member
Goldensavage
VIP Member
Correct, i have a a few that would not read the nand again until the switch was changed. Try this first
yes i can do that i did have a few issues connecting that point could it be possible if ive stuffed that up i would be effecting the nand read? Could it be ive accidentally burnt one of the little resistors and that causing me issues ???
Antalpromille
VIP Member
Yes it could. I got one a few days ago and it had the same problem (a failed RGH-attempt), after i fixed the stby_clk it was again readable by my nand-x.
im thinking we could be onto something however doing a bit of research i did try the alternate point on the back of the motherboard just incase i did stuff it up and i had no luck with that. What is the fix what would i need to do or am i stuffed?
Antalpromille
VIP Member
Clean the area and take a good picture of it so we can see, no one can tell what you need to do before we can see it. If its damaged it will need repair.
poisins
VIP Member
Does console boots (fan is spinning, not just beeps on power-on)? Yesterday I got similar problem, but solved succesfully with bad-flash recovery:
Hope this will help. My trinity wasn't booting at all, but now, 1 - 2 cycles to glitch
- removed power and video, coolrunner cables... nand-x leaved soldered
- shorted all nand pins (both sides) with one wire thread, fixed thread to nand pins with insulating tape, so it connects only to nand pins, nothing else
- plugged in video/av cable, then power
- after 5 sec connected nand-x to console, then to PC
- tried reading nand and got flashconfig with many read errors on first blocks, then everything was good
- erased nand with nandpro (nandpro usb: -e16 0 400)
- and writed ECC without any write errors
- unplugged power and video/av, then removed wire thread from nand pins
- soldered coolrunner and console was succesfully booting to Xell
Hope this will help. My trinity wasn't booting at all, but now, 1 - 2 cycles to glitch
Last edited:
crashxtrme
Full Member
Goldensavage
VIP Member
STBY_CLK is on the wrong pad for starters. It states to use the one next to it. (don't know whether that causes issues)
As everytime i either joined the 2 pads or accidentally soldered to the wrong one i have had issues personally Which has only happend twice
Also, have you got pics of your coolrunner.
As everytime i either joined the 2 pads or accidentally soldered to the wrong one i have had issues personally Which has only happend twice
Also, have you got pics of your coolrunner.
Last edited: