RGH Two xbox's dead after flashing glitch image

[mamaki]

Hello, i have done the glitch hack before and everything goes right, i use Xnand Healer 0.71 with nandpro20e, 360 Multi Builder v0.6.
I flashed the .ecc image, get the cpu key, created the glitch image with dash 13604 and everything works fine.

Now i update all the software, Xnand Healer 0.72, nandpro20e (the same), and 360 Multi Builder 0.7.
First i get the cpu key from a falcon with firmware 14699 by flashing the .ecc image, created the glitch image with dash 14699 and flashed it. Now the xbox is dead. Whats happened??
The same passed with a slim, everything ok, but when i flashed the glitch image the xbox become dead..
And the nand flasher dont find the flash controller. I try with a usb flasher and LPT flasher and had the same result.:eek2:

Someone had the same problem?

Thankyou

 

[Netkar]

lol I have used xnand healer 0.72, nandpro3.0 and 360 multibuilder 0.7, and the same with jasper...

 

[weedpoppin]

maybe you can take a look here :
http://team-xecuter.com/forums/showthread.php?t=74992 and remeber if the xbox wont boot up check your RGH point B (STBY_CLK) happens to me and fix it hope it helps too

 

[mamaki]

the points are all OK, it happens me to 2 xbox's, i flash the .ecc image succefully, i get the cpu key succefully, i build the glith image 14699 succefuly (i think yes, xnand healer builds it). I flashed the nands succefuly, then the xboxs are dead. It dont turn on and i cant flash nand beacuse nandpro does not find the nand.

 

[esbmaepo]

the points are all OK, it happens me to 2 xbox's, i flash the .ecc image succefully, i get the cpu key succefully, i build the glith image 14699 succefuly (i think yes, xnand healer builds it). I flashed the nands succefuly, then the xboxs are dead. It dont turn on and i cant flash nand beacuse nandpro does not find the nand.

Either you have damaged STBY_CLK point or you have a bad flash NAND on your hand. Either way your console wont boot.

If you believe STBY_CLK is ok then you may have to try with a 5v mod to read nand.

 

[spookyman166]

Jaspers are a bastard when it comes to nand... Did you use the inbuilt nand flasher? Or did you do it with Nand X?

ie... Did you flash nand from Xell or Nand X

 

[mamaki]

So i tried the 5v mod on the slim and i have this result:

XnandHealer detects USB and show this:

NandPro v2.0e by Tiros
Looking for usb interface device
Flash Config: 0x00023010
Block Size: 16KB Block Limits: 0x000000..0x000000
0000

then i try to read the nand and get:

Looking for usb interface device
Could not detect a flash controller!
Can not continue

then i try to detect again, now it wont detect anything and shows the same message.

if i turn off the 5V and turn on again it recognizes but stays in the same situation.

im using a usb nand flasher to flash the nand.

where is the 5v mod point on the phat xbox? so i can test it in the falcon.

thanks

 

[Xmarksthesh0t]

this is probably due to your soldering.

 

[dannyperez]

have you been using 13604 nand dumps to build your 14699 image? because this can cause your console to become dead, this has happened to me before and i needed to update my LDV to get it to boot again.

Xmarksthesh0t is right, 9 out of 10 times "could not detect flash controller" is down to bad soldering.

 

[esbmaepo]

So i tried the 5v mod on the slim and i have this result:

XnandHealer detects USB and show this:

NandPro v2.0e by Tiros
Looking for usb interface device
Flash Config: 0x00023010
Block Size: 16KB Block Limits: 0x000000..0x000000
0000

then i try to read the nand and get:

Looking for usb interface device
Could not detect a flash controller!
Can not continue

then i try to detect again, now it wont detect anything and shows the same message.

if i turn off the 5V and turn on again it recognizes but stays in the same situation.

im using a usb nand flasher to flash the nand.

where is the 5v mod point on the phat xbox? so i can test it in the falcon.

thanks

Here is the 5v mod for PHATS:

http://forums.xbox-scene.com/index.php?showtopic=700983

Are you using direct wiring for reading nand or QSB's?

Believe you have a soldering problem.

Maybe post som pics if you got it.

 

[mamaki]

tried the 5v mod on phat and nandpro wont detect anything.

im using direct wires for reading/writing nand.

Is not a soldering problem, i have changed the nand flasher from slim to phat, and phat to slim many times, and confirm all points.

Remember that i read the nand, flash .ecc image, get the cpu key, flash glith image always with the nand flasher soldered... i dont touch him..

dannyperez:

i build 14699 for SLIM using 13604 nand backup, but for PHAT i use 14699 nand backup to build 14699 glitched image.

thanks everyone

 

[diaboliq20]

why would you not just have built the image in multibuilder 0.7 and flashed with Rawflash through xell? - seems the common denominator between you and Netkar is Xnand healer
I have used both Nandpro 2 and multibuilder many times with no issues

and what NAND flasher are you using??

 

[mamaki]

because i never flashed with Rawflash through xell, i started with XnandHealer and everything work fine till this machines..

Im using SPI MTX Nand Flasher, and LPT direct flashing, and no success.

Now i dessoldered Coolrunner, i stay only with nand flasher, but same situation

 

[esbmaepo]

tried the 5v mod on phat and nandpro wont detect anything.

im using direct wires for reading/writing nand.

Is not a soldering problem, i have changed the nand flasher from slim to phat, and phat to slim many times, and confirm all points.

Remember that i read the nand, flash .ecc image, get the cpu key, flash glith image always with the nand flasher soldered... i dont touch him..

dannyperez:

i build 14699 for SLIM using 13604 nand backup, but for PHAT i use 14699 nand backup to build 14699 glitched image.

thanks everyone

Are you using Matrix Nand Flasher?

---------- Post added at 15:21 ---------- Previous post was at 15:11 ----------

because i never flashed with Rawflash through xell, i started with XnandHealer and everything work fine till this machines..

Im using SPI MTX Nand Flasher, and LPT direct flashing, and no success.

Now i dessoldered Coolrunner, i stay only with nand flasher, but same situation

I am also using Matrix Nand Flasher and never had any problem with it. Am using Nand Flasher for Windows to read/write nand.

 

[Netkar]

Yes so we have same problem with 3 console, is not soldering problems.. I think We need a solution for write again nand or to power on xell. Or a new nand (dual nand
Thanks mamaki.
I have nand-x and is the same.. We Hard problems or in image builded from xnand or in write command from xnand also

 

[diaboliq20]

have you guys tried recovering the NAND with a badflash method

 

[Netkar]

have you guys tried recovering the NAND with a badflash method

I'm with iPhone. Do you have some Links? Many thanks

 

[esbmaepo]

I'm with iPhone. Do you have some Links? Many thanks

Read this thread. There are links for 5v mod for both SLIM and PHAT....

 

[diaboliq20]

have a look here mate - it involves shorting the pins on the NAND

 

[dannyperez]

tried the 5v mod on phat and nandpro wont detect anything.

im using direct wires for reading/writing nand.

Is not a soldering problem, i have changed the nand flasher from slim to phat, and phat to slim many times, and confirm all points.

Remember that i read the nand, flash .ecc image, get the cpu key, flash glith image always with the nand flasher soldered... i dont touch him..

dannyperez:

i build 14699 for SLIM using 13604 nand backup, but for PHAT i use 14699 nand backup to build 14699 glitched image.

thanks everyone

when you get to the point of reflashing your slim make sure you update your LDV by one digit through 360 flash tool or options.ini in mutibuilder, thats if you haven't done so already, as for the phat 360 i can't help you with that