Hello i got 3 unlock pcbs 2 works one doesnt work tryed it in a few drives no joy i even soldered the wires straight to the unlock pcb still no joy.can write to the board ok but it wont eject with ck3 pro are xbox when i hit the eject button on the ck3 pro you can see the laser flash. tryed one off the working unlocked broads in the drive and it worked fine so it isnt the drive.soldered the old board back on and it works to.is there anywhere i could get the board repaired.the drive is a 0225 drive.if you can help ponit me in the right way to get it fixed il be very gratefull.many thanks and well done on making great products.
[UK] tx unlock pcb help
- Thread starter doe1200
- Start date
I know it's not much help as u wont get a replacement now, but u really should speak to the reseller u bought it from first I guess
yeah i did talk to the reseller they told me to come here tested with multimeter seems to be getting voltage ok 3.3v
I honestly think u have tried everything u can - if the others worked fine, it seem like u have a faulty PCB especially if it's having the error with eject from the ck3
thats the thing i can write to the board and it comes up in jungle flasher just seems no power is getting to the eject,ah will just a duff board. thanks for your help guys
rdubbs007
VIP Member
I had that same problem with a cold joint, but im a little busy right now to find where it was ill look at this later for you. In the meantime maybe someone else here has had the issue and resolved it? Might be able to lend some insight?
Last edited:
You have a warranty. Use it.
However some people will take this as being the problem with their boards when its not working - when 9/10 its because they didn't read the instructions (the boards are shipped blank and they will not eject or detect in JF - they need to program the board and the instructions tell them how)
In your case however you programmed your board correctly and there is obviously a fault - which can be fixed for you - just return it to your reseller. All official resellers are given manufacturer back warranties.
hi xecuter do you know off anywhere i could get the board checked are repaired by a pro thanks again
I think they are suggesting u send it back to the supplier under your warranty, and they get it repaired/replaced by the wholesale company of TX?
yeah just seen what xecuter said even forwarded it to the reseller cause they told me to come here because they had no knowledge of the board il wait and see what there reply is they are a uk based tx reseller.thanks again guys very much appreciated
Ubergeek
Xecuter Groupie
rdubbs007
VIP Member
no probs rdubbs im sure your a busy man and have your own worries. contacted the reseller hopefully will get it sorted thanks too all at tx
Hi,
Same for me, I have try again and again.
I can write the firmware all seem to work.
But Alway No Drive Detected!
1. liteon 0225
2.
3. Unlocked PCB
4. LT+1.9
5.
6. No Drive Detected (after flash process!!!)
Thanks for help
Same for me, I have try again and again.
I can write the firmware all seem to work.
But Alway No Drive Detected!
1. liteon 0225
2.
3. Unlocked PCB
4. LT+1.9
5.
6. No Drive Detected (after flash process!!!)
Thanks for help
I am in the same situation with 2 PCB's.
Both can be flashed ok, but functional they are a mess.
One of them eject the dvd tray, the console is stuck 30 sec to 1 min to Xbox 360 logo an you either get E64 or Open tray.
The other one, it dosen't even eject dvd-tray.
Also there are 2 lots or factories where the PCB are comming from.
The smooth functional without problems is the one with the white switch for unlocking Spi and green QC Passed sticker.
[ame]http://www.youtube.com/watch?v=FmX7eSKuzkw[/ame]
The one with the problems has the switch black and the QC Passed sticker is golden.
[ame]http://www.youtube.com/watch?v=3bBdPo3yQrk&feature=related[/ame]
Please confirm witch switch and sticker do you have on faulty PCB's.
Hope to resolve it by warranty.
And if this may count, i appreciate the effort from TX to make a total solderless solution, but we could get rid of the mechanical contacts, and spare 1-2$
Soldering 5 wires is not a hard job for anyone who is modding a console.
Both can be flashed ok, but functional they are a mess.
One of them eject the dvd tray, the console is stuck 30 sec to 1 min to Xbox 360 logo an you either get E64 or Open tray.
The other one, it dosen't even eject dvd-tray.
Also there are 2 lots or factories where the PCB are comming from.
The smooth functional without problems is the one with the white switch for unlocking Spi and green QC Passed sticker.
[ame]http://www.youtube.com/watch?v=FmX7eSKuzkw[/ame]
The one with the problems has the switch black and the QC Passed sticker is golden.
[ame]http://www.youtube.com/watch?v=3bBdPo3yQrk&feature=related[/ame]
Please confirm witch switch and sticker do you have on faulty PCB's.
Hope to resolve it by warranty.
And if this may count, i appreciate the effort from TX to make a total solderless solution, but we could get rid of the mechanical contacts, and spare 1-2$
Soldering 5 wires is not a hard job for anyone who is modding a console.
Last edited:
Unfortunately the 2 faulty PCB boards are from arcalide.com and they seem to ignore emails regarding refund or replacement of these xecuter PCB's.
They are from France by he way....
They are from France by he way....