that made no sense to me, might be my english tho! wait for someone else to reply or explain what you just tried to say...
and also, where have you connected j2b1-5 ?
ANSWERED Unable to read nand - "Can not continue" - NandPro v3.0
- Thread starter darkwolf789
- Start date
and also, where have you connected j2b1-5 ?
Ubergeek
Xecuter Groupie
Ubergeek
Xecuter Groupie
This means your nandx is version 2 and you are trying to use nandpro v3 ( or vice versa )
I get that error when i fail to read nand 2or 3times in a row, just reconnect and all fine
Of course using the right nandpro is crucual!
uber why are you not out celebrating new year!?
Sent from my GT-I9100 using Tapatalk
Of course using the right nandpro is crucual!
uber why are you not out celebrating new year!?
Sent from my GT-I9100 using Tapatalk
Ubergeek
Xecuter Groupie
I don't think people seem to understand that there is a real problem here. I have done so many jtag installs that i can't remember since 2009. I have updated to v3 and have not been able to read a single nand since. Nand pro 3.0 gave me a 3 second read on the first nand I tried after the update then errors and never was able to read a nand again. I have tried jasper boards, falcon, and xenon. I have many boards and do this all the time. My solder job is perfect. I can tug and pull on the conenction and it won't move. It is solid. So there is some type of conflict somewhere. Hopefully this will be figured out but it's not the solder job.
maybe you killed it when you updated it.. mine works fine after the update, as long as i solder good enough!:rolleyes2:
like uber said, 99% of the time it's down to the soldering!
NandPro v3.0a by Tiros
Looking for usb interface device
Can not continue
I'm just going to buy a new nand x the fact it started the read for 3 seconds then gave errors means something must have happend to the nanx x. I will just buy a new one and hopefully I will get some reads.
BTW my nand x flashes the coolrunner just fine but oh well
Looking for usb interface device
Can not continue
I'm just going to buy a new nand x the fact it started the read for 3 seconds then gave errors means something must have happend to the nanx x. I will just buy a new one and hopefully I will get some reads.
BTW my nand x flashes the coolrunner just fine but oh well
Ok I got my new nand x today with the v3 coding already on it and it works like a charm. I left the old wire job in the I used for the non-working nand x. All I did was connect the new nand x to the wires already soldered and bam. After I finished reading I hooked the old nand x up the the same connection to make sure it's not a fluke. The verdict is in... Some how the old nand x went bad after updating to v3. It will flash the coolrunner but will not read the nand. Very strange to me but atleast I fixed the problem because I knew it was not a solder issue.
I have too problem with NAND-X v3. I use QSB for Phat for two consolel Jasper's. Soldering Job is perfectly I have some skils. Consoles booting normal after install QSB's but problem is with reading NAND.
NandPro30 says "Incompatible ARM hardware for this version of NandPro !". My NAND-X is new with sticker on package "New V3 Code" I try use NandPro20 but with the same effect.
I try reflash NAND-X with CK3Pro and CK3Pro ver D with this one added cable that is in feedback but Magic FLash write "Failed to autobaud - step1"
Very anoying stop on step 1
All stuf I have baught on ModTraders.co.uk and cool runners looking are oryginal. I think rest of stuff are oryginal.
NandPro30 says "Incompatible ARM hardware for this version of NandPro !". My NAND-X is new with sticker on package "New V3 Code" I try use NandPro20 but with the same effect.
I try reflash NAND-X with CK3Pro and CK3Pro ver D with this one added cable that is in feedback but Magic FLash write "Failed to autobaud - step1"
Very anoying stop on step 1
All stuf I have baught on ModTraders.co.uk and cool runners looking are oryginal. I think rest of stuff are oryginal.
Ok some new news...
I have try read nand ususes Jtag Tool 4.25 and working !
I have Use NandPro 30 but in Jtag Tool i see is NandPro 30a.
I try Jtag with this tutorial http://team-xecuter.com/forums/showthread.php?t=75945
I have try read nand ususes Jtag Tool 4.25 and working !
I have Use NandPro 30 but in Jtag Tool i see is NandPro 30a.
I try Jtag with this tutorial http://team-xecuter.com/forums/showthread.php?t=75945
Ubergeek
Xecuter Groupie
I have try read nand ususes Jtag Tool 4.25 and working !
I have Use NandPro 30 but in Jtag Tool i see is NandPro 30a
can you rewrite that please because im just lost
I have Use NandPro 30 but in Jtag Tool i see is NandPro 30a
can you rewrite that please because im just lost
I have to try dump nand with this tutorial http://team-xecuter.com/forums/showthread.php?t=76193 and nandpro write erorr "Incompatible ARM hardware for this version of NandPro !"
With Jtag Tool 4.25 no eerors nand dumping ok I try manualy dump with nandpro from Jtag Tool 4.25 and working great...
I see many people have problem like mine Mine is solved
With Jtag Tool 4.25 no eerors nand dumping ok
I try manualy dump with nandpro from Jtag Tool 4.25 and working great...I see many people have problem like mine
Mine is solved Certainly was in my case! Most aren't as good at soldering as we like to think we are.
---
I am here: http://maps.google.com/maps?ll=50.804132,-1.157355