Update failure error codes.

N

nubleet

Senior Member
Apr 5, 2012
129
0
They are within tolerance
Edit for numbers
Black: .344v
Brown: 3.2v
Red: .5v
Orange: .01mv (40.4ohm)
Green: 2.9v
Yellow (blue): .3mv (6.15ohm)
 
Last edited:
N

nubleet

Senior Member
Apr 5, 2012
129
0
They are a little low, but I attributed that to the fact that the wiring was still in place. What do the low values suggest? I have replaced the southbridge so I do not believe the chip is the cause. Where else would you suggest that I check?
 
gazcoigne

gazcoigne

BANNED
Jan 31, 2005
1,106
0
Belfast, UK
not thread hijacking or anything but ive came across the exact same situation on a console last night, going to dump the NAND tonight and figure out what happened.

console owner said wifi network went down mid update, and now its stuck in an update loop same as yours. latest m$ update on USB pen fails with same error code (roughly) as does disk update. i must check the hex thing when i get it back later.

hope you get it sorted!! good luck!!
 
N

nubleet

Senior Member
Apr 5, 2012
129
0
I did a reflow on the southbridge first, and then it wouldn't power on, so i reballed it and it powered on. After I realized that it had the same issue, I replaced the southbridge (issue was not resolved)
 
Last edited:
N

nubleet

Senior Member
Apr 5, 2012
129
0
It has always had a Jasper 512 come up in J-Runner. The chips are both labeled "PSB X817692-002 B-A0" then what I am assuming is a serial number? Do they have to be exact?

- - - Updated - - -

It does tell me that the header is wrong and I have to manually select "Jasper 512" in a dialog box that appears.
 
gazcoigne

gazcoigne

BANNED
Jan 31, 2005
1,106
0
Belfast, UK
managed to fix my issue with similar error code

dumped NAND, glitched and got CPU key, figured out dash version and LDV, created retail NAND, flashed and updated to latest with USB, works perfect.

do you have progskeet or demon to read/write nand if the SPI interface is bad?
 
N

nubleet

Senior Member
Apr 5, 2012
129
0
Code: 
===================================================
Friday, November 22, 2013 8:36:06 AM

J-Runner v0.3 Beta (2) Started


WARNING! - Your selected working directory already contains files!
You can view these files by using 'Show Working Folder' Button

Anyone offering hosting servers with unlimited speeds/traffic at good prices (or free :P), pm me on #J-Runner EFnet
Checking Files
Finished Checking Files
Checking Console..
Version: 10
Flash Config: 0x00AA3020
Error: 240 reading block 0
00AA3020
Jasper 512MB
 
N

nubleet

Senior Member
Apr 5, 2012
129
0
gazcoigne said:
managed to fix my issue with similar error code

dumped NAND, glitched and got CPU key, figured out dash version and LDV, created retail NAND, flashed and updated to latest with USB, works perfect.

do you have progskeet or demon to read/write nand if the SPI interface is bad?
Click to expand...
I do have a progskeet 1.2, but I couldn't find any diagrams to wire it up.
 
Martin C

Martin C

VIP Member
Jan 10, 2004
35,981
0
Scotland, UK
www.team-xecuter.com
CHUCKEMZ said:
have you try using a different 360 hard drive to apply the update. seems like the internal hdd may not have enough space free
Click to expand...
System updates have feck all to do with a HDD (for the last time).

- - - Updated - - -

nubleet said:
Yeah. That is the most odd part. Boots to update loop.
Click to expand...
I think it's related to this issue.

Check WP and WE on the NAND.
 
You must log in or register to reply here.