Updated retail NAND now Demon won't glitch

X

xmodpro

Noob Account
Oct 16, 2011
8
0
Ok so I think I really messed something up here and I need some help. Here's what I did.

-Have a Jasper SB on 13599
-Installed Demon & CR rev C with RGH1
-Wrote the glitched image to the Demon
-Everything worked great. The Demon booted to the glitched Dash and the Xbox booted to the retail NAND. Hooray! And because it's RGH1 the boot times were amazing!

Now here's where I became stupid and started messing with things. I wanted the retail NAND to be updated to 16203. So I plugged in the ethernet and updated the retail NAND through XBL. After the update the retail NAND booted just fine with 16203. Then I tried to boot with the Demon to the glitched NAND, but nothing happened. The CR wouldn't even glitch at all. No green light. Then I became more stupid and thought I would reinstall the original NAND dump to the Xbox. After I did that now the retail NAND won't boot at all. I get 3 red lights after 30 seconds or so. So now instead of having a killer Jasper dual NAND RGH1, I have a brick! :facepalm: Can anyone help me out here?
 
M

mm53668

Yes by updating you blew the E-Fuse in the CPU - Once you update you can't go back. You LDV does not match
 
X

xmodpro

Noob Account
Oct 16, 2011
8
0
saxon1978 said:
Now you need to hook up cr for rgh2. Meanwhile ill will create 16203 retail image.
If it's working from this image you will create a glitch image for deamon.
Click to expand...
I do have another Xbox that I can do RGH1 but I need to at least get this one booting from a retail NAND. I sent you my original NAND dump. So where did I go wrong here? How should I have updated the retail NAND instead of updating it through XBL? Becasue if I try this again with another XBOX I want to make sure I don't make the same mistake.
 
MANUMAN

MANUMAN

VIP Member
Jun 11, 2011
591
0
DUBLIN
You cant have a demon with rgh1 it has to be rgh 2 because when you update the xbox retail nand it becomes a split cb hence rgh2 wiring is needed.
 
X

xmodpro

Noob Account
Oct 16, 2011
8
0
saxon1978 said:
You should first update and then install deamon.
Only rgh2
I am updating.
Click to expand...
So the only way to get the updated Dash on the retail NAND is to do RGH2? That stinks. I want RGH1 because boot times are so much better. I've done multiple RGH2's and the boot times are never as good as RGH1. There's no way to update the retail dash without having to switch to RGH2?
 
Krafter

Krafter

VIP Member
Apr 17, 2011
3,737
118
Indiana
No your stuck with RGH2. Wait the R-JTAG. Boot times are going to improve dramatically.


Tapatalk misspelled it. Knot me.
 
X

xmodpro

Noob Account
Oct 16, 2011
8
0
saxon1978 said:
Put your nand in jrunner chose retail 16203-advanced change ldv 7 (in your case one up)
And hit create.

- - - Updated - - -

Now from that image create for deamon and wire for rgh2
Click to expand...
How did you know which LDV to change it to?
I'll just have to try RGH2 now. Thanks for your help. Maybe I'll hold onto that other Xbox for the jrgh.
 
You must log in or register to reply here.