Updating JR Programmer V1

[supertaco]

Windows 8.1 x64

Hi, i'm a noob with all JRunner stuff. I've used to work with an ****** SPI Flasher, and an old pc which i used to program glitcchips. The PC suddenly died.

So i brought a JR Programmer V1, the guy who sold it to me told me that it doesn't came with FW, so i was supposed to flash it. My first problem was the drivers, i used the old good ****** drivers, but they are uncompatible with JR. I deleted them, installed the new firmware and we're ready.

The JR Programmer was factory flashed, so i didn't use the update tool. The thing is, i don't know how to update or flash again the FW. This is what i know:

-Plug JR Programmer, JR Logo shows in JRunner, green light.
-Switch Program close to reset button, still green light.
-Hit reset button, (connect & disconnect sound), red light (bootloader mode)
-Update FW, select PICFLASH_E_1_0_4_ISD_BIT.HEX
-Device Not Found

Return the switch to normal, unplug the usb, wait.... plug again... green light. It doesn't stopped working. But why i cannot update? Do i need install the drivers when the JR Programmer is on Bootloader mode too?

I must be doing something wrong.

And the last, a cuestion... Can i program a x360Ace v3 with this programmer? I tried this

-Connect AceV3, connect JR Programmer to USB
-Select Glitch2m
-Select Program CoolRunner (USB)
-Select RGX Trin_C
-Detects the Xilinx
-Erase
-Error writing... >_<

Any help would be VERY appreciated.

P.S. I've read that if i flash the PICFLASH_E_1_0_4_JRP1_ISD to my JR Programmer, i can program the glitchips but nand reading stop works. Is that true?

 

[BL4K3Y]

The person you bought it from is talking crap.

The JRP comes pre-programmed from the factory and unless he f****d up re-programming the device, it shouldn't need programming.

Did you install the JRP drivers?

Does J-Runner show a black "JR" logo when the device is connected?

 

[jekdyell]

Can i program a x360Ace v3 with this programmer? I tried this

-Connect AceV3, connect JR Programmer to USB
-Select Glitch2m
-Select Program CoolRunner (USB)
-Select RGX Trin_C
-Detects the Xilinx
-Erase
-Error writing... >_<

Any help would be VERY appreciated.

P.S. I've read that if i flash the PICFLASH_E_1_0_4_JRP1_ISD to my JR Programmer, i can program the glitchips but nand reading stop works. Is that true?

flash your JRP with PICFLASH_E_1_0_4_JRP1_ISD to program x360ace.

you will need to modify the jrp a bit for NAND reading,there is a DIY method floating about on the net,or try and get the tx speed upgrade qsb for the jrp

or just flash the PICFLASH_E_1_0_4_ISD_BIT for nand reading when you want to read/write to the nand.

 

[supertaco]

The person you bought it from is talking crap.

The JRP comes pre-programmed from the factory and unless he f****d up re-programming the device, it shouldn't need programming.

Did you install the JRP drivers?

Does J-Runner show a black "JR" logo when the device is connected?

Thanks for your help.
Indeed the one who sold it to me was talking crap. The JRP was ready to go. I have the right drivers and the JR logo appears on JRunner...

I've noticed that when i put the JRP on bootloader mode, windows device manager shows it as: "Input Device Manager" with an exclamation mark!
Is that normal? Because JRunner says:

Device Not Found

flash your JRP with PICFLASH_E_1_0_4_JRP1_ISD to program x360ace.

you will need to modify the jrp a bit for NAND reading,there is a DIY method floating about on the net,or try and get the tx speed upgrade qsb for the jrp

or just flash the PICFLASH_E_1_0_4_ISD_BIT for nand reading when you want to read/write to the nand.

Thanks for your answer, i've seen the DIY method and i'm going to do it

But i'm still unable to do the right trick to update JRP fw... maybe my english it's so bad that i cannot understand the instructions or maybe... it's a bad unit? drivers? i think i got the right ones...

Edit: Now it has the 1.1 DIY update. But still can't flash the fw...