hi just fitted my v2 corona r/w kit.. on my laptop i have a built in card reader when i plug the r/w kit in it comes up in j-runner as a pyishcal drive does not say anything about cornoa 4gb do i need a usb card reader or is this normal thanks wayne
v2 corona
- Thread starter bigwayne
- Start date
nofeloniesyet
VIP Member
corona 4gb shows up like a physical drive it wont show anything about a corona,jus try a read
this is what i get when i try to read nand i will take pic now of my install of the r/w kit
Reading from to C:\Users\serena\Desktop\J-Runner v02 Beta (283) Core Pack\output\nanddump1.bin
System.ArgumentException: Invalid handle.
Parameter name: handle
at System.IO.FileStream..ctor(SafeFileHandle handle, FileAccess access, Int32 bufferSize, Boolean isAsync)
at System.IO.FileStream..ctor(SafeFileHandle handle, FileAccess access)
at JRunner.Forms.LDrives.read()0
Reading from to C:\Users\serena\Desktop\J-Runner v02 Beta (283) Core Pack\output\nanddump2.bin
System.ArgumentException: Invalid handle.
Parameter name: handle
at System.IO.FileStream..ctor(SafeFileHandle handle, FileAccess access, Int32 bufferSize, Boolean isAsync)
at System.IO.FileStream..ctor(SafeFileHandle handle, FileAccess access)
at JRunner.Forms.LDrives.read()0
Reading from to C:\Users\serena\Desktop\J-Runner v02 Beta (283) Core Pack\output\nanddump1.bin
System.ArgumentException: Invalid handle.
Parameter name: handle
at System.IO.FileStream..ctor(SafeFileHandle handle, FileAccess access, Int32 bufferSize, Boolean isAsync)
at System.IO.FileStream..ctor(SafeFileHandle handle, FileAccess access)
at JRunner.Forms.LDrives.read()0
Reading from to C:\Users\serena\Desktop\J-Runner v02 Beta (283) Core Pack\output\nanddump2.bin
System.ArgumentException: Invalid handle.
Parameter name: handle
at System.IO.FileStream..ctor(SafeFileHandle handle, FileAccess access, Int32 bufferSize, Boolean isAsync)
at System.IO.FileStream..ctor(SafeFileHandle handle, FileAccess access)
at JRunner.Forms.LDrives.read()0
Try another SD card reader.
The "cheaper" ones tend to work best (those that you can get for £1.50 on eBay or something lol).
You should also post an image of the R/W QSB (installed of course).
The "cheaper" ones tend to work best (those that you can get for £1.50 on eBay or something lol).
You should also post an image of the R/W QSB (installed of course).
Last edited:
pic of install i have tryed the built in card reader on my laptop and the micro sd to usb reader which is in the pic same results think i may nip to pc world get a cheap card reader
been and bought another card reader and also lent 1 off a friend anybody any ideas on this could the r/w kit be faulty also the dash is 13599
Martin C
VIP Member
The only way the R/W kit would be faulty is if you damaged it during install.
Ensure you connect everything in the right order.
unplug everything from the console.
set the switch to R/W.
connect the PSU to the console.
plug the white adaptor into your SD reader.
plug the SD reader into your PC.
Ensure you connect everything in the right order.
unplug everything from the console.
set the switch to R/W.
connect the PSU to the console.
plug the white adaptor into your SD reader.
plug the SD reader into your PC.
jligg
VIP Member
Make sure you run j runner as admin and try to solder a wire from the ground point on the rw kit to a ground on the board.
Sent from my Galaxy Note II
Sent from my Galaxy Note II
am sure this a card reader issue so am just testing things i set the r/w kit to r/w and tryed to boot the console martin c mention this in a thread i read when searching the console did not boot so thats good i want to test solder points with multi meter but cant find much info i use multi meter allot on dvd drives setting the pots up so if any 1 could point me to some info and what reads i should be getting that would be great thanks wayne
all sorted now went to my old mans tryed his laptop with built in card reader work straight away all glitched and running smooth good glitch times aswell cheers wayne