SAMSUNG MS28 Vendor Intro Failed - Error Message I never seen before.

M

MonkeyDrone

Full Member
Oct 9, 2011
54
0
Heya fellas,
I have a MS28 spoofed as a Liteon-7485.
I have been trying to get the drive into vendor unsuccessfully.
I have tried the Sammy Unlock but that seems to be only for Stock drives.
I tried the troubleshoot of Bad Flash; All 3 methods.
With Method 1 & 2, the dots "....." keep going for infinity and nothing happens.
As for step 3; I followed the guide in Jungle Flasher Tutorial with the CK3 Probe on Page 198 (Basically the 3rd step with Probing the MS28 and throwing it in vendor mode)
I have attached screenshots of the error I'm getting;
Vendor ID: 0x2
Device ID: 0x1C
The photo speaks for itself.

Jungle Flasher Log Text of the whole procedure ---
Sending Vendor Intro to port 0x0000

Status 0x90

Re-sending Vendor Intro:

.........................................................

Parallel flash found with Status 0x70



Sending Device ID request to port 0x0000

Manufacturer ID: 0x2

Device ID: 0x1C

Flash Name: Unknown type

Flash Size: n/a

Unknown flash type Read aborted !

Unknown flash type Read aborted !

Sending Vendor Outro to port 0x0000

------
Any suggestions what's going wrong here?
 
Last edited:
yazzino

yazzino

Senior Member
Jan 30, 2011
137
16
france
MonkeyDrone said:
Already did that bro, that was the 1st option from the 3 options on how to get the drive in vendor mode!....
Click to expand...
so if u have ur key u should try liteon erase or the activate.iso or try half tray open and tell us what happen ok good luck
 
Last edited:
x360ccm

x360ccm

BANNED
Jan 18, 2011
3,616
0
south coast UK
just replace the drive with a orig drive.so it's spoof as a lite on.get a lite on drive and flash the lite on,as that be your orig drive not a sammy.

spoofing surported now.

---------- Post added at 13:48 ---------- Previous post was at 13:47 ----------

yazzino said:
u dont have the key so wy u make black line in the picture of jf .dvd key is black line ??????
Click to expand...
maybe thats his key hey

a screen shot of your firmware tool 32 tab be good to see if you can.
 
Last edited:
R

rjh79

Full Member
Apr 5, 2011
64
8
Brighton England
Hi i had this problem the other day and found that my x360 pro was the problem i unplugged it and used a sata port on a via 6421 with the drivers removed, clicked intro and used the probe 3 with a power cycle and worked fine. after about 4 hours of hair tuggin
 
M

MonkeyDrone

Full Member
Oct 9, 2011
54
0
dgenx said:
just replace the drive with a orig drive.so it's spoof as a lite on.get a lite on drive and flash the lite on,as that be your orig drive not a sammy.

spoofing surported now.

---------- Post added at 13:48 ---------- Previous post was at 13:47 ----------



maybe thats his key hey

a screen shot of your firmware tool 32 tab be good to see if you can.
Click to expand...
As far as the key goes; when I press the outro button even though it never properly went into the vendor mode; it shoots out the key. Now I'm not sure if it is the proper key cause if its not and I end up erasing the drive, I'm screwed.

As for the Firmware Tool32 tab, its completely empty, it doesn't load up anything in there. No source whatsoever.
Next step I'm going to do is now take a liteon drive and spoof it with lt+ 1.1 with the key and see if it works. This might take a while.

---------- Post added at 00:05 ---------- Previous post was at 00:04 ----------
rjh79 said:
Hi i had this problem the other day and found that my x360 pro was the problem i unplugged it and used a sata port on a via 6421 with the drivers removed, clicked intro and used the probe 3 with a power cycle and worked fine. after about 4 hours of hair tuggin
Click to expand...
Hmmm, I don't have a Via 6421 card =X

I'll go with the above method I posted in the previous post and see if that works. Might not have to go through this.

Cheers.
 
M

MonkeyDrone

Full Member
Oct 9, 2011
54
0
Alright, I have good news and bad news.

I didn't have a LiteOn drive around, just a BenQ drive.
I spoofed the BenQ as a liteon 7485 with LT+ 1.1 and I used the key that was being shown after I was pressing Outro/ATA Reset with the weird Vendor Mode. It is playing games. My dashboard is still pre1316.

In a nutshell, I believe I can't update the dashboard with a spoofed BenQ because It'll be looking for a LiteOn drive and try to update the drive with a liteon official firmware.

Or am I wrong and I can update the dashboard to the latest version with the BenQ drive in there. If I can, do I need to put in the original BenQ Firmware with the Key I have extracted from the MS28.

Or my other option would be to use the MS28 and replace its' firmware with an official ms28 firmware with the key I have and update the dashboard with the ms28 drive plugged in the XBox.

I am not fully aware of how the xbox360 would try to update the drive's firmware.

Any help would be appreciated, thanks.
 
You must log in or register to reply here.