Whennnn??? :'(
- Thread starter Mr.Bilz2
- Start date
scott1503
VIP Member
i think tx have said they aint going to touch it, might be wrong. they have bigger fish to fry.
that being said someone like 15432 might be trying to work on a solution
that being said someone like 15432 might be trying to work on a solution
GeekHeat
VIP Member
probably not worth it for xecuter since its only a small percentage of Winchester's made and not everybody with a Winchester will want it as rgh.
scott1503
VIP Member
Plus if it was me I would rather buy a jasper to have a rgh and let tx continue on the road to success with the xbox one
GeekHeat
VIP Member
nobody knows. Like scott1503 has said 15432 might be looking into it.
- - - Updated - - -
jaspers are the most reliable xbox motherboards in my opinion.
Antalpromille
VIP Member
currently there are not so many winchesters, so people mostly don't care.
I tried several 'easy' ways (soldering to balls, secret mfg bootloader, counting from the CPU init, 1BL glitch, 'fixing' the rgh stability).
several of them failed, others were forsaken at half.
There is still one good idea left, but as I said earlier, no time for it :smile:
in case of fail of that last idea - there won't be hack method (until somebody steal another mfg bootloader)
Descend
Senior Member
I'd prefer them to work on the Xbox One - there is a much higher demand for this.
Plus, it's quite easy to grab a cheap console that is exploitable.
-Descend
Plus, it's quite easy to grab a cheap console that is exploitable.
-Descend
Antalpromille
VIP Member
If you take TX at their word then they won't be. Xecuter said himself the the CR4 will be the last product they produce. There never was a clarification on whether or not that was just for the 360 or if the included the One. It's not unlike them to drop something and fail to mention it.
MTWallet
VIP Member
Aww man, why didn't you tell me that before? (Not that I asked :wink
I bought a used slim (trinity) and put the DemoN and CR4 in that but I already had a retail jasper that I didn't RGH.
Antalpromille
VIP Member
well, probably becouse you didnt askAww man, why didn't you tell me that before? (Not that I asked :wink
trinitys are fine to but i can tell you that there have been alot of failed trinitys on my desk but no jaspers at all with hardware failure.
MTWallet
VIP Member
Hmmm, decisions decisions. Have a RJTAG'ed Falcon, a retail Jasper and now a RGH CR4/DemoN combo on the trinity. Was going to get rid of the 2 phats and just use the slim, but maybe just keep 'em now.
nofeloniesyet
VIP Member
i have reworked thousands upon thousands of consoles in my years doin this,6 jaspers ever true rrod bga issues ever came to me,2 was customers fault,and recently a 7th one now that came in fine,e76 while rghing,and fixed that with new ics ethernet chip,then it eventually rrod again while trying to glitch,very very reliable consoles the jaspers are.they run 150 watt cause of the smaller processor dyes and therefore dont consume as much energy thus not creating enough heat to cause thermal stress and flex the board enough to break the bga balls.the lower temps also keep the solder from degrading as badly as it does in older phats.all that just added up to the best board out there tbh.
I know its been said more than a few times on this forum. Given a choice most of us would go with jasper for reliability.Aww man, why didn't you tell me that before? (Not that I asked :wink
i've must have said this 100 times, especially when i'm posting in a xenon thread telling someone to throw their sh*t in the trashAww man, why didn't you tell me that before? (Not that I asked :wink