hey, needmsome expertise please. been doing this for a long while now, and wanted to update my chip from an x2.6 to a X3, so all i did was remove my x2.6 and put in the X3(yes it's turned the right way) hooked up the power/eject assably and the wires and pins are the same as the x2.6 only the x3 is turned the other way. i got the flash bios screen and i know how to make bios discs, so i made a couple just in case of a bad burn! after the flash is shut down, and when i powered up, i get a blank scren with no A/V at all. MS dash boots fine, and if i put back in my x2.6 that works fine. so i put in the x3 again, and again, boot from the backup using the power/eject trick, and flash once again, with a newly made iso bios cd. And guess what? yep! blank and no A/V everytime i try to flash the same sh*&t happens. i have a 1.2-1.5 xbox and my d0 wire is installed from the top, i went to cllege for soldering/computer repair, so i do know that it is not my perfct soldering job, plus my x2.6 works everytime like a charm. i run evox, build 3935, 250gbhd, and my setup is perfect, besides the ten minute swap turned into a all day and night thing! i can't figure this out, so i has to be a X3 problem or you know what to do. thanx and help me please. Bboy
x3 bios flash and now just getting blank screen. help pleas
- Thread starter dirtybboy
- Start date
Re: x3 bios flash and now just getting blank screen. help p
well your trying to flash to x3.1959 bios right on your x3 mod chip? well if u are try doing this... " 1MB Bank
Bank 1234: on on off off (Set to this when flashing first time with FlashBIOS)"
if cd method dont work try using http method i did 2 flashes with the http method and it worked perfect everytime.
well your trying to flash to x3.1959 bios right on your x3 mod chip? well if u are try doing this... " 1MB Bank
Bank 1234: on on off off (Set to this when flashing first time with FlashBIOS)"
if cd method dont work try using http method i did 2 flashes with the http method and it worked perfect everytime.
Re: x3 bios flash and now just getting blank screen. help p
could be the 13 and 14 pins on the lcp. http://www.teamxecuter.com/index.ph...5&start=0&postdays=0&postorder=asc&highlight=
could be the 13 and 14 pins on the lcp. http://www.teamxecuter.com/index.ph...5&start=0&postdays=0&postorder=asc&highlight=
360 with error code 0110
ok so i picked up a 360 the other day with error code 0110 i have reflowed the ram chips 3 times with my heatgun top and bottom of board and even tried a 4 hour oven bake on the board and still get error 0110 upon boot-up don't have a reflow station can't afford it between jobs at the moment i have done the x-clamp fix and the hybryd x-clamp to this too with no luck so any suggestions from anyone what to try next before i just toss the thing in the trash LOL
ok so i picked up a 360 the other day with error code 0110 i have reflowed the ram chips 3 times with my heatgun top and bottom of board and even tried a 4 hour oven bake on the board and still get error 0110 upon boot-up don't have a reflow station can't afford it between jobs at the moment i have done the x-clamp fix and the hybryd x-clamp to this too with no luck so any suggestions from anyone what to try next before i just toss the thing in the trash LOL
Re: 360 with error code 0110
I have the same error code. It sucks, i've had limited success with varying the tension of the heatsink screws, but that lasts only a few hours before it freezes again.
I have the same error code. It sucks, i've had limited success with varying the tension of the heatsink screws, but that lasts only a few hours before it freezes again.