yes its all okay there do you know that i mean that my xbox boots only with microsoft bios ? the x3 bios dont work and the CHIP IS DISABLED THIS IS WHY I HAVE A RED LIGHT
i hate it..
i hate it..
X3 Dont Work..
- Thread starter vampy
- Start date
ok now im confused again
a quick press of the power button does________?
a long press of the power button does_________?
what load on either presses?
do you get a frag? Are you sure your connection are rock solid?
a quick press of the power button does________?
a long press of the power button does_________?
what load on either presses?
do you get a frag? Are you sure your connection are rock solid?
ok
a quick press does that the xbox booting normal with the microsoft bios
the long press does the same
and sometimes i get this problem like here:
3) Power on and xbox starts 2x then power flashes red and green (this is called FRAG)
-- For initial installs this indicates something is not properly solder with your Header Pin / Wire Harness install.
-- Tip for the header pin install (Highly recommend doing header pin install - Always). Apply flux to the pins going through the LPC holes. This will draw the solder into the lpc holes and ensure a solid connection between the lpc and header pins. Have a small dap of solder on the tip of the soldering tool. Touch this to the back side of the exposed part of the pin and apply the solder to the opposite side right at the base of the lpc hole and header pin. the solder should melt right into the hole. be careful not to let solder bridge any gaps or splash onto other traces.
-- LPC Rebuild. I recommend getting some 30AWG wire from any local electronics store. Solder the wire to the motherboard connection first, then shape, strip and solder the other end to the header pin. Just take your time.
bu i have soldert the pins often always the same the chip dont work...
edit: flux ???
a quick press does that the xbox booting normal with the microsoft bios
the long press does the same
and sometimes i get this problem like here:
3) Power on and xbox starts 2x then power flashes red and green (this is called FRAG)
-- For initial installs this indicates something is not properly solder with your Header Pin / Wire Harness install.
-- Tip for the header pin install (Highly recommend doing header pin install - Always). Apply flux to the pins going through the LPC holes. This will draw the solder into the lpc holes and ensure a solid connection between the lpc and header pins. Have a small dap of solder on the tip of the soldering tool. Touch this to the back side of the exposed part of the pin and apply the solder to the opposite side right at the base of the lpc hole and header pin. the solder should melt right into the hole. be careful not to let solder bridge any gaps or splash onto other traces.
-- LPC Rebuild. I recommend getting some 30AWG wire from any local electronics store. Solder the wire to the motherboard connection first, then shape, strip and solder the other end to the header pin. Just take your time.
bu i have soldert the pins often always the same the chip dont work...
edit: flux ???
Well I dont know what to tell you, hopefully Xecuter, or someone else will look at this fourm and know the solution.
lol I guess put it back on, but first check to see if everything still looks good. and be extra carefull this time. If I were you however I would wait for another person to tell me the same thing... so if you want keep it off for now.
ok i have a question 
open the picture..
http://www.mymtw.de/files/userconfigs/28362_PCB.JPG
have soldert it to the second position..
open the picture..
http://www.mymtw.de/files/userconfigs/28362_PCB.JPG
have soldert it to the second position..
The 2nd is the correct position. Just done my 1.6 box today and its my first install and I've had no problems. I would say you have a problem with the D0 connection so check the grey wire and the other points on the LPC rebuild itself.
reflashing litoen 74850C
HI,
I need to reflash my liteon7 and it had been flashed by someone else.
do i have to extract the key again???
and what the hardware should i use to reflash if nessacery>
please help...
thank you
HI,
I need to reflash my liteon7 and it had been flashed by someone else.
do i have to extract the key again???
and what the hardware should i use to reflash if nessacery>
please help...
thank you
Re: reflashing litoen 74850C
Yes, you will need the key again. Do you have a dummy.bin file? That is where the key is stored. If not you'll have to retrieve it again, yourself.
Also, do you know what the drive has been flashed with? If it's flashed with LT, you will have to do an MRA hack! There are many ways to do this, I personally have an xecuter pro kit, and the probe v2 attachment!
Yes, you will need the key again. Do you have a dummy.bin file? That is where the key is stored. If not you'll have to retrieve it again, yourself.
Also, do you know what the drive has been flashed with? If it's flashed with LT, you will have to do an MRA hack! There are many ways to do this, I personally have an xecuter pro kit, and the probe v2 attachment!
Re: reflashing litoen 74850C
I have dummy bin..
how could i know what the drive has been flashed with.?
what is MRA hack??
right now i dont have any extra hardware
I have dummy bin..
how could i know what the drive has been flashed with.?
what is MRA hack??
right now i dont have any extra hardware
Re: reflashing litoen 74850C
Oh, perfect! Since you have dummy.bin you don't need to worry about the MRA hack or anything like that.
All you need to do is plug your dvd drive into your computer with a sata cable, and power it, either with the xbox 360 itself (not recommended) or the connectivity kit.
I highly suggest you read the jungleflasher tutorial, it'll probably answer a lot of your questions. It's, dare I say, idiot proof! lol
Oh, perfect! Since you have dummy.bin you don't need to worry about the MRA hack or anything like that.
All you need to do is plug your dvd drive into your computer with a sata cable, and power it, either with the xbox 360 itself (not recommended) or the connectivity kit.
I highly suggest you read the jungleflasher tutorial, it'll probably answer a lot of your questions. It's, dare I say, idiot proof! lol
Re: reflashing litoen 74850C
It was! but then someone went and made a better idiot!Acester said:
Re: reflashing litoen 74850C
It was! but then someone went and made a better idiot!
ha ha so true bh
It was! but then someone went and made a better idiot!
ha ha so true bh
Re: reflashing litoen 74850C
I had conected it also i tryied to do the same as tutorial but after varification ok...then i connected to the 360, and the drive has not reflashed.Acester said: