- Dec 14, 2003
- 5
- 0
I've installed a pin header on a 1.6 (non b version) for an X3 install. I soldered everything according to the install pic on teamxecuter's website, and after several resolders I could not get pin 9 to produce a voltage. I checked the smartxx install diagram and they had pin 9 jumpered over to another location on the board so I went with that. What I have now is the following.
D0
Chip turned on with short power-on = Red LED on X3 front panel and it frags.
Chip turned off with long power on, Blue LED on X3 front panel - boots to M$ dashboard.
Chip turned on with Both power and eject = Purple LED on X3 front panel on first boot, alternates red/blue on 2nd and 3rd boot - boots to M$ dashboard
If I understand correctly, this tells me that d0 is working
5v Chip LED and 3.3 volt chip LED
Both light up when chip is active.
LAN/HD
Both light up and show activity when chip is active.
Pins and voltages
Pin 1 - Supposed to be < 1volt according to the lpc troubleshooting guide, i'm getting a high voltage # (8-10 volts). Not sure what to think of this. It's a clean solder with no over-solder anywhere.
Pin 2 - 0 Volts - Ground (Tested OK by hooking black to it and checking a 3.3 pin)
Pin 3 - 0 Volts - Says that this is LFRAME and is disconnected in v1.3 xboxes and newer - is this true?
Pin 4 - NO PIN
Pin 5 - 3.3 Volts
Pin 6 - NO PIN
Pin 7 - 3.3 Volts
Pin 8 - 3.3 Volts
Pin 9 - 3.3 Volts
Pin 10- 3.3 Volts
Pin 11- 3.3. Volts
Pin 12- 0 Volts - Ground (Tested OK by hooking black to it and checking a 3.3 pin)
Pin 13- 3.3 Volts
Pin 14- 3.3 Volts
Pin 15- 3.3 Volts
Pin 16- NO PIN
As far as I can tell this should all be OK barring no other issues. The LPC troubleshooting guide lacks 1.6 information so I had to piece a bit together. I can't confirm whether or not Pin 3 is a problem, and the high voltage on Pin 1 had me scratching my head a bit for it's supposed to be .2 according the LPC troubleshooting page.
Anybody have any ideas?
D0
Chip turned on with short power-on = Red LED on X3 front panel and it frags.
Chip turned off with long power on, Blue LED on X3 front panel - boots to M$ dashboard.
Chip turned on with Both power and eject = Purple LED on X3 front panel on first boot, alternates red/blue on 2nd and 3rd boot - boots to M$ dashboard
If I understand correctly, this tells me that d0 is working
5v Chip LED and 3.3 volt chip LED
Both light up when chip is active.
LAN/HD
Both light up and show activity when chip is active.
Pins and voltages
Pin 1 - Supposed to be < 1volt according to the lpc troubleshooting guide, i'm getting a high voltage # (8-10 volts). Not sure what to think of this. It's a clean solder with no over-solder anywhere.
Pin 2 - 0 Volts - Ground (Tested OK by hooking black to it and checking a 3.3 pin)
Pin 3 - 0 Volts - Says that this is LFRAME and is disconnected in v1.3 xboxes and newer - is this true?
Pin 4 - NO PIN
Pin 5 - 3.3 Volts
Pin 6 - NO PIN
Pin 7 - 3.3 Volts
Pin 8 - 3.3 Volts
Pin 9 - 3.3 Volts
Pin 10- 3.3 Volts
Pin 11- 3.3. Volts
Pin 12- 0 Volts - Ground (Tested OK by hooking black to it and checking a 3.3 pin)
Pin 13- 3.3 Volts
Pin 14- 3.3 Volts
Pin 15- 3.3 Volts
Pin 16- NO PIN
As far as I can tell this should all be OK barring no other issues. The LPC troubleshooting guide lacks 1.6 information so I had to piece a bit together. I can't confirm whether or not Pin 3 is a problem, and the high voltage on Pin 1 had me scratching my head a bit for it's supposed to be .2 according the LPC troubleshooting page.
Anybody have any ideas?