Xbox 360 Messup

nofeloniesyet

VIP Member
Jan 16, 2011
4,830
128
Nowhere
I am always insecure about hanging on a Demon to a Trinity console because I have seen so many break down
Also I don't know about the Demons availability as of now.
If it helps out I have some of the slim Demons complete kits that I would sell to Felonies or Krafter but no one else
unfortunatley coronas havent proved to be any better imho.its kinda hit or miss on any of em really.jaspers def gave the least issues for me over the years.i still have 10 jasper gpu on hand,but never had to use one of em.they will eventually start breaking in higher numbers like the rest though,only a matter of time.
 

stucknvegas

VIP Member
Oct 25, 2012
656
0
Cypress CA. USA
I have only seen 3 Jaspers that I could not Fix out of 100 I have sold
Also I have only had 2 Corona 250 gigs broken both bad xgpu
I don 't want to hijack this thread ITS NOT MINE
 

nofeloniesyet

VIP Member
Jan 16, 2011
4,830
128
Nowhere
ok so i received it today,first thing i did was remove EVERYTHING! the cap c2c5 was burned up,and also missing the pad on the right,so i had to sodler it from pad that was left on the left,to the tiny via above it to complete the circuit,ofc new cap pulled from a dead trinity :)

KoH0dUn.jpg
above board where demon was, nice and clean :)

mbNokRD.jpg

above another pic of clean demon area. got it off nice n clean with all mobo pads intact :)

cfMD4LN.jpg

above is pic of new cap soldered to pad and via above it,thats why its sitting cock eyed :)

35HzIRw.jpg

above better pic of the added cap on c2c5

zBEguim.jpg

above demon cleaned and ready for install.

oh yea,box now boots stock with no issues. progress........
 
  • Like
Reactions: AaronG and ablegepu

nofeloniesyet

VIP Member
Jan 16, 2011
4,830
128
Nowhere
You do a heck of a job to :biggrin:
grr after couple minutes running it rrod and shuts off,i noticed some stray solder in a few dif places,trying to track issue down now.
 

ablegepu

VIP Member
Jan 3, 2014
925
0
Alabama U.S
Those caps are tiny and it takes a lot of practice and a steady hand to solder them to the pads especially if you have to make a new pad out of the left over trace or via like that. this is one thing I have had lots of practice with myself, removing those tiny caps and measuring the capacitance then soldering it back in place. Most of the time I can make it look like it had never been bothered, it would be so much easier if I had a setup like you got where I could just reflow the components with hot air because its not easy to do with a soldering iron and a pair of tweezers
 

Oggy

Staff member
Troll Eating Dogs
Mar 1, 2010
3,346
128
Nofel is skilled with a pair of tweezers. He uses them every time he needs a piss.
 
  • Like
Reactions: ablegepu and AaronG

nofeloniesyet

VIP Member
Jan 16, 2011
4,830
128
Nowhere
Nofel is skilled with a pair of tweezers. He uses them every time he needs a piss.
and yet i still manage not to piss all over my balls like you do oggy,lol

box cuts on soon as powers applied,fan goes crazy rampin up,and rrod then shuts down,then itll cut itself on again,and keep repeating itself.error was 0032.still investigating here....usually 0032 is either broken cpu rst (which im not seeing nothing) or reball or replace southbridge...
 
Last edited:
  • Like
Reactions: ablegepu and AaronG

nofeloniesyet

VIP Member
Jan 16, 2011
4,830
128
Nowhere
and yet i still manage not to piss all over my balls like you do oggy,lol

box cuts on soon as powers applied,fan goes crazy rampin up,and rrod then shuts down,then itll cut itself on again,and keep repeating itself.error was 0032.still investigating here....usually 0032 is either broken cpu rst (which im not seeing nothing) or reball or replace southbridge...
ok,it ws powering on as soon as you hooked power up,and fan would go crazy after a few seconds on,then red dot,and power off,then power back up itself and kept repeating that.

took everything back out,measured i/o resistors at r1t18-r1t9,r1t9 was measuring 20+k ohm,was posed to be 10k,so replaced it.also replaced c1t2 cap that ground on demon was goin to,and finally c2c4,like you mentioned in earlier posts.and now console no longer powers up itself after adding power,and it boots and stays running :) so looks like we got it fixed now.will test tonight before i continue with demon/cr install.been running for 20 min now no issues at all,by far longest its ran,and no longer cut off and back on to red light,and have to power cycle it,so everything is lookin great now!
 
Last edited:

nofeloniesyet

VIP Member
Jan 16, 2011
4,830
128
Nowhere
[emoji16] awesome work!


Sent from my iPhone using Tapatalk
lol,its runnin fine,only one issue left now.every few sec the sync lights on rf module light up like you hit the sync button.so gotta track that down now.boy you did a number on this one,lol
 

nofeloniesyet

VIP Member
Jan 16, 2011
4,830
128
Nowhere
Lol I sure did, I'm glad I sent it to you [emoji38] :)


Sent from my iPhone using Tapatalk
spoke too soon,back to red dot 0010,looks like this ones gonna be a continous error code chasing box.