FIXED xbox 360 wont boot due to faliure in nand flasher( help)

[nitonito]

i tried to update with the nand_flasher_360_for_xbox_360_v1.2

i got orig_nand.bin

a whiles flashing Image.15574-dev.bin that i created

had power off (electric problem) after the power had being restored tuned on the console and came with red light with error E 79


i Googled and lent its an hdd problem so i took of the hdd, power cords and hdmi cable and waited for 5mins
i plugged back the power and hdmi cord without the hdd.
but still got the same error.

i turned off the xbox 360 and pressed the eject button loaded to a blue screen and got stacked


xbox cant load any more please need help any tits will do

thanks to all.

 

[Taijigamer2]

Are u able to boot into xell? if so just reflash your 15574-dev image to xbox. either rename it to updflash.bin and place on usb stick and run xell or flash it direct with nand-x or jrprogrammer v2. Good luck.

 

[nitonito]

thanks for the quick replay

it gets stucked at xell
i guess that's the image shown in blue back ground what i'v uploaded.

 

[Slayertex6]

By the pics, you have a phat xbox. Make a regular RGH image or use the pre-made ecc to boot Xell. Looks like your building a dev image that was probably built using RGbuilder.

 

[Martin C]

Disconnect both DVD and HDD, then try booting to Xell.

 

[nitonito]

okay thanks m8 trying out that.

 

[nitonito]

thanks much all for your help my console is back online and active.

i appreciate much with all the quick responds,

will also be given help to others in the forum with things i know

thanks much all.

 

[Slayertex6]

It'd be cool if you could elaborate on what exactly you did to solve your problem. Just for us curios ones.

 

[nitonito]

It'd be cool if you could elaborate on what exactly you did to solve your problem. Just for us curios ones.

well thats cool m8

note if the xell get stacked when loading you will have to unplug all drives first.

Update your JTAG/RGH
Current Dashboard: 16537

Things you will need:
-XeBuild GUI 2.091
-Backup NAND
-CPU Key
-USB Flash Drive (Formatted to FAT32)
-Flash360(if you don't have your NAND backed up)

Instructions:
Skip to step 5 if you already have a backup NAND and your CPU key
1. Boot into XeLL (with the console turned off, press the eject button)
2. Copy CPU key down onto notepad (if you are connected via ethernet to your network, simply type in the IP address and then copy the CPU key from there; if you are not, manually copy the code)
3a. If you are connected to the network page (for XeLL), click "download" next to the "Raw Flash" section
3b-1. If you are not connected to the network, run flash360 on your Xbox (place on USB drive and launch using XeX menu, FSD, etc)
3b-2. Press X to backup your NAND
3b-3. Once completed, exit the application
4. Power down the Xbox (and remove flash drive if you used flash360)
5. Launch XeBuild GUI 2.091
6. Click open next to source file and select your flashdmp.bin
7. Click save next to output path and select the root of your flash drive (save as updflash)
8. In the keys section, paste your CPU key
9. At the bottom right of the screen, press check KV (this makes sure the CPU key is correct and will properly build your image)
10. In kernel version, select 2.0.16537 (if not already selected)
11. Double check build type, motherboard, XeLL, and SMC Hack (JTAG ONLY)
12. Press "Generate Hacked Image"
13. Once completed, unplug your flash drive
14. Plug your flash drive into the Xbox (with the console OFF)
15. Boot into XeLL (press eject button with the console off)
16. The image should begin to flash (rawflash v4 initiated, etc)
17. Once complete, power down the Xbox
18. Unplug flash drive
19. Power on the Xbox

Congratulations, you have successfully updated to dashboard 16357

well thanks again for all your tits.