Xbox boots xell but stays on xbox 360 boot logo

[ObeyNation]

Console Type:Falcon
NAND size: 16
Dashboard version: latest
CB version: ??


Description of problem: Hey i have rjtaged by xbox it boots almost instant to xell but when i go to boot to the dashboard i see the xbox 360 logo and the little animation moving in the logo but the light doesnt stay soild green on the rjtag chip almost like its not glitching to go to the dash?

Was the console working before you started: Yes while it was stock

pics of soldering: https://drive.google.com/folderview?...ms&usp=sharing

Post out

Version: 10
Power Up
Waiting for POST to change
Post 0C 
Post FC 
Post 0C 
Post FC 
Post 0C 
Post FC 
Post 0C 
Post FC 
Post 0C 
Post FC 
Post 0C 
Post 8C - Panic - SYSTEM_CALL 
Post 0C 
Post 8C - Panic - SYSTEM_CALL 
Post 0C 
Post FC 
Post 0C 
Post FC 
Post 0C 
Post FC 
Post BC 
Post 0C 
Post FC 
Post 7C 
Post 0C 
Post 8C - Panic - SYSTEM_CALL 
Post FC 
Post 8C - Panic - SYSTEM_CALL 
Post 8F - Panic - MAINTENANCE 
Post 8F - Panic - MAINTENANCE 
Post 10 - Payload/1BL started 
Post 11 - FSB_CONFIG_PHY_CONTROL 
Post 12 - FSB_CONFIG_RX_STATE 
Post 1B - RC4_DECRYPT 
Post 1C - SHA_COMPUTE 
Post 1D - SIG_VERIFY 
Post 1E - BRANCH 
Post 20 - CB entry point reached 
Post 21 - INIT_SECOTP 
Post A0 - Panic - VERIFY_SECOTP_6 
Post 04 
Post 8C - Panic - SYSTEM_CALL 
Post 04 
Post 8C - Panic - SYSTEM_CALL 
Post FE 
Post FC 
Post FC 
Post 04 
Post 84 - Panic - INSTRUCTION_STORAGE 
Post 0C 
Post 84 - Panic - INSTRUCTION_STORAGE 
Post FE 
Post FC 
Post 84 - Panic - INSTRUCTION_STORAGE 
Post 04 
Post 8C - Panic - SYSTEM_CALL 
Post 84 - Panic - INSTRUCTION_STORAGE 
Post 04 
Post FE 
Post FC 
Post 84 - Panic - INSTRUCTION_STORAGE 
Post 8C - Panic - SYSTEM_CALL 
Post FC 
Post 18 - FETCH_CONTENTS 
Post 1B - RC4_DECRYPT 
Post 1C - SHA_COMPUTE 
Post 1D - SIG_VERIFY 
Post 1E - BRANCH 
Post 20 - CB entry point reached 
Post 21 - INIT_SECOTP 
Post 22 - INIT_SECENG 
Post FE 
Post 04 
Post 8C - Panic - SYSTEM_CALL 
Post 0C 
Post FC 
Post FE 
Post FC 
Post 0C 
Post FC 
Post FE 
Post 84 - Panic - INSTRUCTION_STORAGE 
Post 8C - Panic - SYSTEM_CALL 
Post 84 - Panic - INSTRUCTION_STORAGE 
Post 8C - Panic - SYSTEM_CALL 
Post FC 
Post FC 
Post 84 - Panic - INSTRUCTION_STORAGE 
Post 04 
Post 84 - Panic - INSTRUCTION_STORAGE 
Post 8C - Panic - SYSTEM_CALL 
Post 0C 
Post 84 - Panic - INSTRUCTION_STORAGE 
Post FC 
Post 11 - FSB_CONFIG_PHY_CONTROL 
Post 1B - RC4_DECRYPT 
Post 1C - SHA_COMPUTE 
Post 1D - SIG_VERIFY 
Post 1E - BRANCH 
Post 20 - CB entry point reached 
Post 21 - INIT_SECOTP 
Post A0 - Panic - VERIFY_SECOTP_6 
Post FE 
Post FC 
Post 84 - Panic - INSTRUCTION_STORAGE 
Post FC 
Post 84 - Panic - INSTRUCTION_STORAGE 
Post FC 
Post 84 - Panic - INSTRUCTION_STORAGE 
Post FC 
Post 8C - Panic - SYSTEM_CALL 
Post FC 
Post FC 
Post 84 - Panic - INSTRUCTION_STORAGE 
Post FC 
Post 0C 
Post 04 
Post FC 
Post 0C 
Post 84 - Panic - INSTRUCTION_STORAGE 
Post 8C - Panic - SYSTEM_CALL 
Post 84 - Panic - INSTRUCTION_STORAGE 
Post FC 
Post 84 - Panic - INSTRUCTION_STORAGE 
Post FC 
Post 11 - FSB_CONFIG_PHY_CONTROL 
Post 1B - RC4_DECRYPT 
Post 1C - SHA_COMPUTE 
Post 1D - SIG_VERIFY 
Post 1E - BRANCH 
Post 20 - CB entry point reached 
Post 21 - INIT_SECOTP 
Post 22 - INIT_SECENG 
Post 2F - RELOCATE 
Post 2E - HWINIT 
Post 33 - FETCH_CONTENTS_4BL_CD 
Post 34 - HMACSHA_COMPUTE_4BL_CD 
Post 35 - RC4_INITIALIZE_4BL_CD 
Post 36 - RC4_DECRYPT_4BL_CD 
Post 37 - SHA_COMPUTE_4BL_CD 
Post 3A - BRANCH 
Post 40 - Entrypoint of CD reached 
Post 42 - FETCH_HEADER 
Post 44 - FETCH_CONTENTS 
Post 45 - HMACSHA_COMPUTE 
Post 47 - RC4_DECRYPT 
Post 48 - SHA_COMPUTE 
Post 4B - LZX_EXPAND 
Post 4E - FETCH_OFFSET_6BL_CF 
Post 4F - VERIFY_OFFSET_6BL_CF 
Post 51 - LOAD_UPDATE_2 
Post 50 - LOAD_UPDATE_1 
Post 52 - BRANCH 
Post 58 - INIT_HYPERVISOR 
Post 5A - INIT_XEX_TRAINING 
Post 60 - INIT_KERNEL 
Post 61 - INIT_HAL_PHASE_0 
Post 62 - INIT_PROCESS_OBJECTS 
Post 64 - INIT_MEMORY_MANAGER 
Post 65 - INIT_STACKS 
Post 66 - INIT_OBJECT_SYSTEM 
Post 67 - INIT_PHASE1_THREAD 
Post 68 - Started phase 1 Initialization + INIT_PROCESSORS 
Post 69 - INIT_KEY_VAULT 
Post 6A - INIT_HAL_PHASE_1 
Post 11 - FSB_CONFIG_PHY_CONTROL 
Post 1B - RC4_DECRYPT 
Post 1C - SHA_COMPUTE 
Post 1D - SIG_VERIFY 
Post 1E - BRANCH 
Post 20 - CB entry point reached 
Post 21 - INIT_SECOTP 
Post 44 - FETCH_CONTENTS 
Post 45 - HMACSHA_COMPUTE 
Post 4B - LZX_EXPAND 
Post 4D - DECODE_FUSES 
Post 51 - LOAD_UPDATE_2 
Post 52 - BRANCH 
Post 59 - INIT_SOC_MMIO 
Post 5A - INIT_XEX_TRAINING 
Post 5B - INIT_KEYRING 
Post 5C - INIT_KEYS 
Post 5F 
Post 61 - INIT_HAL_PHASE_0 
Post 6A - INIT_HAL_PHASE_1 
Most Fails(cumulative): 0xA0
Shutdown
Power Up
Waiting for POST to change
Post 8C - Panic - SYSTEM_CALL 
Post 0C 
Post FC 
Post 0C 
Post 8C - Panic - SYSTEM_CALL 
Post FC 
Post 8C - Panic - SYSTEM_CALL 
Post 0C 
Post FC 
Post 8C - Panic - SYSTEM_CALL 
Post FC 
Post 0C 
Post FC 
Post 8C - Panic - SYSTEM_CALL 
Post FC 
Post 8C - Panic - SYSTEM_CALL 
Post FC 
Post 8C - Panic - SYSTEM_CALL 
Post FC 
Post 8C - Panic - SYSTEM_CALL 
Post FC 
Post 0C 
Post 1C - SHA_COMPUTE 
Post 1D - SIG_VERIFY 
Post 1E - BRANCH 
Post 20 - CB entry point reached 
Post 21 - INIT_SECOTP 
Post 22 - INIT_SECENG 
Post 2F - RELOCATE 
Post 2E - HWINIT 
Post 31 - FETCH_HEADER_4BL_CD 
Post 33 - FETCH_CONTENTS_4BL_CD 
Post 34 - HMACSHA_COMPUTE_4BL_CD 
Post 35 - RC4_INITIALIZE_4BL_CD 
Post 36 - RC4_DECRYPT_4BL_CD 
Post 37 - SHA_COMPUTE_4BL_CD 
Post 3A - BRANCH 
Post 40 - Entrypoint of CD reached 
Post 44 - FETCH_CONTENTS 
Post 45 - HMACSHA_COMPUTE 
Post 46 - RC4_INITIALIZE 
Post 47 - RC4_DECRYPT 
Post 48 - SHA_COMPUTE 
Post 4B - LZX_EXPAND 
Post 4E - FETCH_OFFSET_6BL_CF 
Post 4F - VERIFY_OFFSET_6BL_CF 
Post 51 - LOAD_UPDATE_2 
Post 50 - LOAD_UPDATE_1 
Post 52 - BRANCH 
Post 58 - INIT_HYPERVISOR 
Post 5A - INIT_XEX_TRAINING 
Post 61 - INIT_HAL_PHASE_0 
Post 63 - INIT_KERNEL_DEBUGGER 
Post 64 - INIT_MEMORY_MANAGER 
Post 65 - INIT_STACKS 
Post 66 - INIT_OBJECT_SYSTEM 
Post 67 - INIT_PHASE1_THREAD 
Post 68 - Started phase 1 Initialization + INIT_PROCESSORS

 

[Martin C]

The debug light shouldn't be solid green once it's glitched. You shouldn't see it again.

 

[ObeyNation]

The debug light shouldn't be solid green once it's glitched. You shouldn't see it again.

But in xell it stays on? is it because it is debugging? Also what would happen is the the chip would turn green then when i see the xbox 360 animation it would turn off and stay on that screen. i can still see the green in the logo glowing and moving though.

 

[mrdrifta]

Try fixing up your JTAG ALT qsb. I had a jasper that would constantly freeze on Post 69 - INIT_KEY_VAULT until i removed the qsb and installed diodes like the BOXXDR method

 

[ObeyNation]

Try fixing up your JTAG ALT qsb. I had a jasper that would constantly freeze on Post 69 - INIT_KEY_VAULT until i removed the qsb and installed diodes like the BOXXDR method

but it boots to xell so does that still mean its a soldering problem

 

[mrdrifta]

Wouldn't hurt to try. Or adjust the ohm jumper for 470/330 ohms. Is this the same console you posted about here: http://team-xecuter.com/forums/showthread.php?t=141653
Then please post new install pictures of your JTAG qsb. (Like the repair of r2p12)

Also have you tried writing a normal Jtag image to the console? (untick Aud_clamp in j-runner when building image)

 

[ObeyNation]

Wouldn't hurt to try. Or adjust the ohm jumper for 470/330 ohms. Is this the same console you posted about here: http://team-xecuter.com/forums/showthread.php?t=141653
Then please post new install pictures of your JTAG qsb. (Like the repair of r2p12)

Also have you tried writing a normal Jtag image to the console? (untick Aud_clamp in j-runner when building image)

Yes its the same console, i havent fixed the r2p12 going to tonight but would that make a difference on why it boots to xell almost instant but when it boots to dashboard its stuck on the xbox animation its not frozen because the green part is glowing and moving ?

 

[mrdrifta]

xell and freeboot both boot slightly different i think(could be wrong).

If you want to test if the boards okay, flash a stock nand image back to the console and remove 5v wire from RJTAG chip. If your console boots fine then it could be an SMC Config seting that needs changing(See Here:http://team-xecuter.com/forums/showthread.php?t=95054)

If it doesn't boot, the R2P12 is your problem. Post a clear picture of it and someone may be able to see if there is damage or not.

 

[ObeyNation]

ok i will try that thanks

 

[ObeyNation]

I was going to flash stock but I decided to play with the dips the it started to boot fine ? funny but at least that's a good thing I will go ahead and replace the r2p12 tonight , does anybody know how to tell what drive came with a Xbox ? Because I have the key just need to know what drive originally came with the unit thanks


Sent from my iPhone using Tapatalk

 

[DayvG]

I'm pretty sure if you load your nanddump and hit the KV info tab it will show the drive under OSIG.


Doing my thing using Tapatalk

 

[chase]

I was going to flash stock but I decided to play with the dips the it started to boot fine ? funny but at least that's a good thing I will go ahead and replace the r2p12 tonight , does anybody know how to tell what drive came with a Xbox ? Because I have the key just need to know what drive originally came with the unit thanks


Sent from my iPhone using Tapatalk

advice below was given on your other post : http://team-xecuter.com/forums/showthread.php?t=141653

your post_qsb could use some work.. use lots of flux and touch it up

have you gone through all dip, voltage, ohm settings ?

also, why do you need to know the original drive.. the console is RGH'd .. you can use any drive

 

[ObeyNation]

advice below was given on your other post : http://team-xecuter.com/forums/showthread.php?t=141653



also, why do you need to know the original drive.. the console is RGH'd .. you can use any drive

Really i can use any drive i dont even need to flash it ? and sometimes if i boot the xbox it gets stuck on that screen but if i boot it with rater it goes al the way to the dash board but i have to remove the rf board or it wouldnt be able to boot the system so i think once i fix the r2p12 tomaro i should be fine thanks for all the help so far

 

[chase]

Really i can use any drive i dont even need to flash it ? and sometimes if i boot the xbox it gets stuck on that screen but if i boot it with rater it goes al the way to the dash board but i have to remove the rf board or it wouldnt be able to boot the system so i think once i fix the r2p12 tomaro i should be fine thanks for all the help so far

no.. you can use any drive as long as you flash the console's dvd key to it .. you don't necessarily need the original drive model

 

[ObeyNation]

no.. you can use any drive as long as you flash the console's dvd key to it .. you don't necessarily need the original drive model

OK, but i have to spoof the drive correct

 

[chase]

OK, but i have to spoof the drive correct

all you have to do is load the latest CFW for the drive you're using into target then manually spoof the console's dvd key and flash the drive

 

[ObeyNation]

Hey would I be able to just jump the r2p12 ?


Sent from my iPhone using Tapatalk

 

[ObeyNation]

If not can someone post a link of what I should get ? I understand it's a 10 k resistor but the pic doesn't seem like the one on the board can I use http://m.ebay.com/itm/290984490893?nav=SEARCH&sbk=1 as well as
http://m.ebay.com/itm/321050800866?nav=SEARCH&sbk=1 or only this will work ? http://m.ebay.com/itm/290984490893?nav=SEARCH&sbk=1 thanks
Sent from my iPhone using Tapatalk

 

[chase]

1206 smd resistor is too big for a replacement .. you can use the ones from the 2nd link or find smaller size smd resistors

you want to be looking for 0603 or 0805 SMDs ..

 

[ObeyNation]

1206 smd resistor is too big for a replacement .. you can use the ones from the 2nd link or find smaller size smd resistors

you want to be looking for 0603 or 0805 SMDs ..

http://m.ebay.com/itm/321050800866?nav=SEARCH&sbk=1&afsrc=1 so I can use these ? And this is the correct one http://bit.ly/1beG4ie sense it's a 0805 . Chase I really appreciate your help , you have greatly helped me out thanks again


Sent from my iPhone using Tapatalk