Xbox nand wont boot -Glitch or Retail

[advancedservers]

Hi,

I have installed my new demon and no I cannot boot from xbox nand.

If I flash stock nand to demon it boots fine, if i flash glitch nand to demon it boots fine. Just will not boot from xbox nand.

Any Ideas??

 

[BL4K3Y]

Is your CR set to NOR or PRG?

Have you programmed the CoolRunner with the relevant EN XSVF?

Are you able to read both NANDs fine?

 

[advancedservers]

to boot glitch nand from demon i have the cr on nor but for stock nand on demon i have to set it to prog.

I have programmed coolrunner with trinity_demon.xsvf.

I can read and write to both nands ok..... well they both match...

 

[BL4K3Y]

Keep the switch set to NOR at all times - even when programming.

 

[advancedservers]

just rewrote the nand with cr set to nor but still no luck??

 

[manwithoutname]

1. You're using CoolRunner Rev C or CR3 Lite?

2. If using CoolRunner Rev C, did you connect the EN points between the DemoN addon and the Coolrunner?

3. Did you program the CoolRunner using the DemoN with EN points connected between the addon and Coolrunner?

If you had provided photos then we would have to ask less questions.

 

[advancedservers]

1. CR rev A
2. I have Solder from pin (as shown in guide) to en point.
3. Yes.

Sorry about no pics camera not working.. I can use my iphone if you wish...

 

[manwithoutname]

write your ecc image to your onboard NAND and get the console to boot xell from there (you might need to re-program the coolrunner with standard trinity timing file for this).

Check your LDV from xell and cross check with the LDV value of your original NAND dump and report back.

 

[advancedservers]

Fuse set 7 has 4 f's

there are 2 ldvs in jrunner one on left is 3 and one on right is 4

 

[manwithoutname]

You need the one on your left, so how come your original NAND dump has an LDV value of 3 while your actual console's NAND has an LDV value of 4?

Have you ran any updates after you attempted the glitch?

 

[advancedservers]

Im not sure I bought the console from ebay.

 

[manwithoutname]

Create a retail NAND image using J-Runner with the correct LDV value and see if that will boot. Make sure the original NAND dumps are safe and backed up at all time.

 

[advancedservers]

Correct LDV value being 4?

 

[manwithoutname]

Yes, LDV @ 4. Did this console boot stock NAND when you got it ?

 

[advancedservers]

yes booted stock nand ok... I can still boot stock nand now but only form Demon Nand.....


Just created stock image in jrunner by

1. Select origianl nand
2. select dash version 14719
3. select retail
4. change LVD of left side to 4
5. select create image
6. write image to xbox360 nand

 

[manwithoutname]

So does it work or not?

 

[advancedservers]

no still wont boot from xbox nand

 

[manwithoutname]

Upload your initial NAND dump and glitch image to a location and PM me the URL. Also if you can add some pictures of the install that might help.

 

[advancedservers]

Will do now

 

[Martin C]

yes booted stock nand ok... I can still boot stock nand now but only form Demon Nand.....


Just created stock image in jrunner by

1. Select origianl nand
2. select dash version 14719
3. select retail
4. change LVD of left side to 4
5. select create image
6. write image to xbox360 nand

Did you go back to 'Advanced / Confirm LDV' after making the change (and before creating the image)?